PRODUCTS & EQUIPMENT


Machinery DRAWBENCHES


100,000 Lb. (50 Ton) Aetna Standard 3 Die Drawbench, 100 Ft. (30 m) Draw, 3” (76 mm) O.D. Maximum Tube, 1” (24 mm) Minimum Finish Draw, 280 kW, SCR Thyristor Controls, Variable Speed, Barrel Rollover Feed, Single Chain (12584)


65,000 Lb. (30 Ton) Montbard 3 Die Drawbench, 118 Ft. (36 m) Draw, 1 5/8” (42 mm) Maximum Incoming O.D., 1” (24 mm) Minimum O.D., 450 kW D.C. Variable Speed with SCR Thyristor Drive, Single Chain (12585)


DRAWBLOCKS


84” (2134 mm) Marshall Richards Model VNCB 84 Spinner Block, 300 HP D.C. Drive, 0-938 m/Min. (3077 FPM) Draw Speed, 44 mm - 6 mm (1.75”- 0.236”) Tube Draw, 8 Basket Carrousel, 7.2 Ton Draw Pull (12586) 84” (2134 mm) Marshall Richards Model VNCB 84 Spinner Block, 350 kW D.C., 0-1100 m/Min. (0-3600 FPM), 48 mm - 6 mm (1.9”- 0.236”) Tube Draw, Basket


International Corp. Buying, selling and appraising used metalworking machinery for the strip,


COPPER TUBE MACHINERY FOR SALE NEW OFFERING - Located in Tunis, Tunisia


All Machines to be sold individually (Machines Run on 380/415 Volt, 50 Hz or DC SCR) Conveyor, 8 Ton Draw Pull (12587)


54” (1370 mm) Marshall Richards Model H4T Horizontal Tube Drawing Blocks, 48mm (1.875”) Maximum Entry O.D., 6 mm (0.236”) Minimum Finish O.D., 0-405 m/ Min. (0-1330 FPM), 10 Ton Pull, 113 kW D.C. Drive w/Telemecanique SCR Thyristor Drive THREE AVAILABLE (12588/12589/12590)


SCHUMAG COMBINED DRAWING MACHINES (6 AVAILABLE)


Schumag KZ-P-1B, 4 mm - 25 mm (0.157”- 1”), 0-60 m/Min. (0-200 FPM), 75 HP, 3 Ton Pull, 6 m (20 Ft.) Maximum Cut Length, w/ Coiler (12591)


Schumag KZ-R-1S, 4 mm - 25 mm (0.157”- 1”), 15-50 m/Min. (0-200 FPM), 50 HP (37 kW), 4 Ton Pull, 3 - 6 m (10 - 20 Ft.) Cut Lengths, w/Coiler (12592)


Schumag KZ-P-1S, 4 mm - 25 mm (0.157”- 1”), 0-60 m/Min. (0-200 FPM), 75 HP (55 kW), 3 Ton Pull, No Coiler (12593)


Schumag KZ-P-1S, 6 mm - 28 mm (0.236”-


1.1”), 15-60 m/Min. (50-200 FPM), 75 HP (55 kW), 3 m - 6 m (10-20 Ft.) Length, 3 Ton Pull, No Coiler TWO AVAILABLE (12594/12595)


Schumag KZP-1B/5, 6 mm - 28mm (0.236”- 1.1”), 0-60 m/Min. (0-200 FPM), 75 HP (55 kW), 3 Ton Pull w/Coiler (12596)


OTHER MACHINES AT THIS PLANT


Ripoche Roller Hearth Annealing Furnace for Copper Coils, 3 Zone, Gas-Fired, New 1995, 1450 mm (57”) Hearth Width, Radiant Tube, Maximum Temp. 650 Deg. C (1200 Deg. F), Water Cooling (12597)


Automated Solutions Straight Length Tube Bundling Machine, New 2000, Tube Range 9.5 mm - 54 mm (3/8”- 2”) O.D., 3 - 6 m (10-20 Ft.) Lengths, Hopper Load 4535 Kg (10,000 Lb.) Max., Descrambler, Vertical Tube Magazine, 5 Taping Heads, 4 Rotating Heads (12603)


Matrasur I.D. Shot Blaster Cleaner for 6


mm - 60 mm (¼”- 2 ¼”) O.D. Tubes, New 1989 (12601)


50 Ton Trayvous Truck Scale, Model TY50, New 2002, Capacity 50 Tons (110,000 Lb.), In-ground (12598)


Krollman HRA-4/65 Hydraulic Squeeze Pointers, 55 mm (2.16”) Maximum Tube O.D., 4 Die, 11 kW, THREE AVAILABLE (12616/12617/12618)


Stevens & Bullivant Rotary Swager, 65 mm (2 ½”) Max. Tube. O.D., Belt Type Rotary Swager, 15 kW (12605)


Stevens & Bullivant Rotary Swager, 100 mm (4”) Max. Tube O.D., Belt Type Rotary Swager, 15 kW (12606)


Carbide Dies and Plugs - Huge Inventory - Over 2500 Carbide Dies from 5mm to 50mm - Over 3800 Carbidge Plugs from 4mm to 44mm (12670)


COMPLETE COPPER FITTINGS DEPARTMENT


For Tees and Elbows (12604)(To Be Sold In


COPPER TUBE PLANT & MACHINERY FOR SALE Hundreds of Machines Suitable for Copper, Aluminum, Brass, and Steel Tube and Rod.


All Machines to be sold individually - All located in Sydney, Australia EXTRUSION PRESS


3500 Ton BLH Oil Hydraulic Extrusion Press, Double Action with Piercer, Loma T40 Automatic Billet Saw w/PLC Controls, Granco Clark Gas-Fired Billet Furnace, underwater runout to eliminate oxidation, 178mm - 305mm (7” - 12”) Dia. Billets, Complete Runout System, Automated Shell Storage System (12734)


DRAWBENCHES


60,000 Lb. (30 Ton) Vaughn 5 Die, 27m (90 Ft.) Draw, 400 HP DC, Barrel Rollover Feed (12736)


90,000 Lb. (40 Ton) Farmer Norton 1 or 3 Die, 15.8m (52 Ft.) Draw, 100 HP, Barrel Rollover Feed (12738))


90,000 Lb. (40 Ton) Hydraulic Tube Expansion Bench, 13.7m (45 Ft.) to expand tube up to 206mm (8 1/8”) (12737);


50,000 Lb. (25 Ton) Mannesmann Meer 3 Die, 23m (75 Ft.) Draw, 300 HP, Barrel Rollover Feed (12735)


DRAW BLOCKS


84” (2134mm) MRB Spinner Block, Model VNCB84, New 1991, 0 - 1200m/min. (0 - 3937 FPM), 300 KW, 30mm - 4mm (1.2” - 0.157”) Draw Range, 8 Station Carrousel (12739)


84” (2134mm) Vaughn Rotobloc Spinner Block, 0 - 731m/min. (0 - 2400 FPM), 350 HP, 50mm - 6.35mm (2” - 1/4”) Draw Range, 8 Station Carrousel (12740)


84” (2134mm) Vaughn Inverted Tube Drop 14


Block, Model 84-24-54, 2134mm (84”) Working Face, 450 HP, Pointer, for 50mm - 19mm (2” - 3/4”) Draw, 0 - 610m/min. (0-2000 FPM) (12741)


84” (2134mm) Vaughn Inverted Tube Drop Block, 2794mm (110”) Working Face, 450 HP, for 50mm - 19mm (2” - 3/4”) Draw, 0 - 600m/min. (0 - 1980 FPM) (12742)


FOUNDRY


Asarco Shaft Furnace, 10 Tons/Hr., Gas- Fired, Vertical Elevator Feed, 8.5m (28 Ft.) Height, Feeding into either of the following Casters:


Ascast/Douglass Continuous Copper Billet Caster for 152mm - 273mm (6” - 12”) Dia. Billets w/406mm - 1220mm (16” - 48”) Log Length (12764); or


Semi-Continuous Vertical Caster for either copper billets or slabs w/20 Ton Holding Furnace. Makes 2 strand copper logs up to 273mm Dia. or Slabs 200mm (7.8”) Thick x 950mm (37.4”) Max. Width (12765)


FINISHING EQUIPMENT


Schumag Model 0B Combined Draw, Straighten, Cut & Coil Machine for 3.2mm - 7mm (1/8” âØÐ 1/2”) Tube, Flying Saw, Eddy Current Tester, Schumag Inverted Coiler for coils or straight lengths (12744)


Vaughn/Ruesch Straighten, Cut & Coil Line for 6mm - 25mm (1/4” - 1”), 0 - 137m/min. (0 - 450 FPM), 2133mm (84”) Coil Payoff, 12 Roll Straightener, Vaughn Flying Cutoff Saw, Ruesch Coiler, Eddy Current Tester (ECT) for


John Conroy Machinery International Corporation - USA Tel: (+1) 203-484-0400 IMT December 2015/January 2016 www.internationalmetaltube.com


either straight lengths of 3 - 7m (10 - 23 ft.) or coils (12753)


Schumag Copper Tube Level Winding Line, New 1991, for 3.18mm - 25mm (1/8” - 1”) Dia., 0 - 450m/min. (0 - 1475 FPM), 84” Basket Payoff, Straightener, Eddy Current Tester, Rotary Cutoff, Winder for 1050mm (41.3”) Coil O.D. x 305mm (12”) Traverse, Schumatronic II Controls (12760)


Eddy Current Test (ECT), Marking & Bundling Line for straight lengths from 25mm âØÐ 206mm (1” - 8”) O.D. tubes including unscrambler, single tube feed, ECT Station, Matthews Paint Marker, 20 Ft. Bundling Station, Scale and Cyklop Bundle Strapper (12748)


Draw, Straighten, Coil Join, In-Line Anneal and Finish Line to produce half hard copper tube 12.7 - 19.1mm (1/2” âØÐ 3/4”) Dia. in straight lengths 5 - 6.1m (16 - 20 Ft.) or coil form including 84” (2134mm) Basket Payoff, Cleaning Station, Coil Joiner, Accumulator, 400 KW Inductoheat Tube Annealer, Quench, Lomatic Drawbench, Hydraulic Flying Shear and Coiler (12756)


Bronx Model 6 CR 7 Rotary Straightener, 6 Roll, for 19mm - 203mm (3/4” - 8”) O.D. tube, 0 -15m/min. (0 - 50 FPM), Entry & Exit Tables, up to 6.1m (20 Ft.) table length, 228mm (9”) Dia. x 355mm (14”) Face Rolls, 2 x 12 HP Motors, Incising Tube Etch Marker/Printer (12731)


Bronx Model 6 CR 2§½ BW Rotary Straightener, 6 Roll, for 6mm - 22mm (1/4”


- 7/8”) O.D. tube, 2.6 - 73m/min. (12 - 240 FPM), 2 x 3 HP, 415 Volt, 3 Ph., 50 Hz Motors (12762)


Mackintosh-Hemphill Model AN Rotary Straightener, 6 Roll, for 12.7mm - 44mm (1/2” - 1 3/4”) O.D. tube, 0 - 137m/min. (0 - 450 FPM), Entry & Exit Tables, Roll Size 152mm x 241mm (6” x 9 1/2”), 2 x 4 KW Varispeed Motors, Incising Tube Etch Marker/Printer (12763)


Draw, Straighten, Cut and Coil Line for 19.1mm - 31.8mm (3/4” - 1 1/4”) copper tube, 84” (2134mm) Basket Payoff, Hydraulic Squeeze Pointer, Schumag Size II Cam-Driven Draw Station with 80/40 HP Drive, 2 Plane Straightener, Paint Marker, ECT, Flying Shear, Runout for up to 6.1m (20 Ft.) straight lengths, Loma Mann Tube Coiler (12754)


Packaging Line for annealed coils, New 1993, automatically takes coils from Roller Hearth Furnace, seals in plastic bags, boxes, stacks, weighs, labels, and palletizes into loads per customer order. Takes either pancake or level wound coils of 20” - 27” (508mm - 686mm) Dia. (12733)


Mitchell Hydraulic Push Pointer, 33,000 Lb. capacity, for 25mm-70mm (1” - 2 3/4”) tube, single tube, 2 Die reduction w/Hydraulic Unit (12743)


Hydraulic Squeeze Pointer for up to 75mm (3”), 100 Ton capacity, Entry Feed Rack, 7 §½ HP 300 Liter Hydraulic Unit, Entry Rack (12752)


Loma Model T-40 Billet Saw, 1016mm (40”) Fax: (+1) 203-484-4499


E-m


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32