THE GOOD OIL!
Whether mineral or synthetic, the quality of oil used in any machine will have a major bearing on its performance and life expectancy.
Here, Royal Melbourne Golf Club turf technician, Luke Spartalis, gives the lowdown on the lifeblood of any machine and poses the question – mineral or synthetic?
As machinery has evolved, so too have the lubricants associated with their use. Turf technicians are now faced with an enormous selection of fully synthetic, semi-synthetic, biodegradable oils and greases and, of course, the traditional mineral oil-based range.
Engine Oil
Engine oil lubricates all metal surfaces inside the engine while dissipating the resultant heat of the combustion process. The selection of the appropriate oil is important because the life of an engine depends on the quality of oil used, but not all oils are the same. Diesel engine oil differs from petrol engine oil in that it is developed to deal with the increased heat of compression found in diesel engines and contains more detergents to deal with the additional combustion by-products. They also contain anti-foaming agents that are not needed in petrol engines. Newer synthetic engine oils available, particularly diesel specified, have been developed with the aim of resisting thermal breakdown, sludge formation and oxidation. Increased drain intervals and fuel efficiency, due to the reduced 'drag' created by higher viscosity oils, are other benefits associated with their use. However, switching from a mineral oil to synthetic based oil in a well-used engine is not a straight forward procedure. Synthetic engine oils contain an Ester-based oil which has excellent natural detergency. This means that it will clean heat any oxidative generated varnish deposits from internal surfaces, the resulting suspended deposits clogging both filters and passageways. Worn engines should be flushed before employing the use of synthetic oils and monitored closely. The same is true for gearboxes and other systems.
106 Hydraulic Oil
The hydraulic system generates a lot of discussion around the turf equipment maintenance industry, in particular the use of biodegradable oils. Advancements are continuing to be made with the next generation of synthetic hydraulic fluids known as polyalkylene glycol oils (PAG). Having been trialled for some time in the United States, these fluids have the benefit of being less harmful to turf in the event of a spill (even when hot), with the added advantage of increased service intervals which goes some way in offsetting the initial higher cost associated with their use. However, while some attributes are desirable, some others are not. Corrosion, cavitation (due to viscosity issues) and filter media incompatibility are just some of the possible problems associated with their use.
While the use of these oils does not necessarily void the manufacturer’s warranty, thorough research is recommended before use, as component failure or performance issues may not be covered.
Whatever the choice, cleanliness and
regular service intervals are paramount to extending the life of hydraulic systems. Contamination of the hydraulic system can be prevented in several ways. Firstly, contrary to popular belief, ‘new’ hydraulic oil itself can be contaminated. It can become contaminated during storage or may be shipped dirty from the supplier. Poorly maintained breathers or vents, or the use of high-pressure water cleaners around these areas, can also result in the fluid being compromised, while dirt ingress via worn or damaged shafts and wiper seals on actuators is another possibility.
Of course, the most common cause of
As a tool to monitor oil condition, oil sampling is an effective method in
determining the general health of a machine’s hydraulic system
contamination is through sloppy and inadequate maintenance procedures. Most hydraulic hose suppliers use high- speed cutting equipment to manufacture hydraulic hoses. While it’s a very effective method of cutting wire strand hose, it also produces metal and rubber particles that could damage precision components. Always thoroughly clean finished hose assemblies with compressed air and new O-rings should also be fitted if equipped. The large capacity of hydraulic systems means that oil replacement is generally a costly exercise. The manufacturer’s guidelines are the best gauge to determine service intervals, however, unusual or extreme conditions may require more frequent servicing. As a tool to monitor oil condition, oil sample analysis is an effective method in determining not only oil replacement intervals, but also gives a window into the general health of a machine's hydraulic system. Moisture, dust and dirt and component wear are measured and, through the use of trending graphs, accurate analysis is achieved and unnecessary and costly maintenance avoided. Sampling is quick and easy with results available either as hard copy or online.
Cutting Fluids
While fully equipped machine shops employ the latest in cutting fluid technology, golf course workshops can also benefit, albeit on a much smaller scale. For those with cylinder grinding equipment, cutting fluid is generally used, particularly when grinding bedknives as it dissipates heat and produces a high finish, along with suppressing airborne grinding particles. Mineral oil-based coolants are available, however, due to contamination
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124