Production • Processing • Handling
Fig. 1. Four custom-designed progressing cavity pumps were piped to a common header.
Custom diluent injection pumps
Thomas Böhme shares a case study that showcases a smart solution devised for a major energy transporter.
W
ith a goal of reaching the highest operational efficiencies at the storage facility, a customer was looking to install a pumping system that would
take the heavy crude oil from the tanks and blend it with diluents to lower the viscosity of the crude oil to be pumped to the main pipeline for distribution. As the crude oil sits in storage tanks over a long period of time, lighter product settles to the top and the heavier product goes to the bottom. Crude oil is drawn off the bottom of the tanks first and this is where most amount of diluent injection is required. As the product changes in viscosity there is a constant need to adjust the amount of diluent being used. Netzsch approached the design of this pumping system with progressing cavity pumps to take care of operating issues associated with constantly changing viscosity.
Custom pump design A critical design issue was the extremely cold operating temperatures during the winter months. With ambient conditions of -30 to -40°C and diluent temperatures as cold as -22 to -25°C, Netzsch engineers needed to carefully consider the elastomer selection for this application. Because the company’s progressive cavity pumps would operate outdoors, it was determined to use a reduced wall stator with heat tracing to insure that a -5 to 0°C operating temperature was maintained within the elastomer. In addition, three resistance temperature detectors (RTD) were to be mounted in each pump to provide feedback data to the control system. To compensate for the cold temperatures, Netzsch
64
www.engineerlive.com
designed a rotor that is slightly oversized to keep the interference fit at sub-zero temperatures. Tis presented an additional hurdle at assembly time. Te solution for assembling a stator on an oversize rotor was to pack the stators in ice in order to make assembly possible.
By using four custom-designed progressing cavity pumps piped to a common header, Netzsch was able to provide the customer with the level of diluent injection control that he was looking for. With the new system, the customer has the ability to run from one to all four pumps and with the use of VFDs, he will have complete control over the diluent injection. Te large pump size also allows the customer to run the pumps slower for a greater life cycle – a critical maintenance advantage in the extremely cold operating environment. l
For more information ✔ at
www.engineerlive.com/iog
Thomas Böhme is with Netzsch in Germany.
www.netzsch.com
Fig. 2. The large pump size means that pumps can be run slower for a greater life cycle.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84