Advertisement Feature
TECHNOLOGY IN ACTION UNI SPLIT GLAND®
The splittable cable gland from the UNI Dicht® system Minimum parts for maximum efficiency. PFLITSCH extends its range of splittable cable entries with the fully
splittable UNI Split Gland® plastic cable gland. The cable gland body and the pressure screw consist of two halves, the sealing inserts are slit at the side and thus allow preassembled cables to be placed in them. The special point about the UNI Split Gland®: the splittability of the cable gland body allows the whole of the hole diameter (M25) to be used for feeding through prefitted plugs.
Advantages • Protection class IP 67
• Allows a cable gland to be replaced without interruption of production (deinstallation/installation can be done without the cable having to be removed)
• M25 connection thread • For cable diameters of 2.0 mm to 20.5 mm • TPE-V sealing inserts from the UNI Dicht® modular range
he UNI Split Gland® is based on the UNI Dicht® principle and therefore ensures the cable is dependably sealed without being irreparably cut into or severely indented. All TPE-V sealing inserts size E 154 from the UNI Dicht® range – from the solid to the multiple-cable sealing insert – can be used with the split cable gland.
T This product reliably seals cables with diameters
from 2.0 mm up to 20.5 mm. The softsquashing action exerted by the sealing insert over a large area of the cable sheath, the seal in the plane of the split and a further seal at the connection thread ensure that the gland achieves IP 67 protection in accordance with EN 60529. The UNI Split Gland® made from polycarbonate also excels with strain relief in accordance with EN 50262 and an operating temperature range of -20°C to +80°C.
UNI Split Gland®
Replacement needed – no problem The splittability of the cable gland allows not only preassembled cables to be installed, through its simple construction and low number of components it also offers the advantage of quick and safe installation – without needing to remove already installed cables or interrupt on-going production. The UNI Split Gland® can be opened again at any time without great effort to allow cables to be installed or reinstalled later.
Conventional developments
Installing the UNI Split Gland® is quick and easy thanks to its few components: place the cable into the sealing insert – PFLITSCH has a practical set of spreading pliers available to help with this – fit the two halves of the cable gland body around the cable already in the sealing insert, bring the two
UNI Split Gland®individual parts
Walter Logan & Co Ltd Tel 0208 492 9704
sales@walterlogan.com
The back of the UNI Split Gland®with a sealing on the connection thread
halves together ready to engage and finally engage them. The cable gland body is now installed in the housing – either screwed into the thread or fastened with a splittable counter nut from the inside – and the sealing insert pushed into it. Then the two halves of the pressure screw are placed around the cable, locked with one another and screwed on to the cable gland body.
enter 802
32 MARCH 2014 | ELECTRICAL ENGINEERING
/ ELECTRICALENGINEERING
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52