FASTENER + FIXING TECHNOLOGY Think big
two basic problems with big bolts. One is that they take a massive amount of torque to tighten. The second is that they have a nasty habit of working loose. When told that the bolts on the gearbox of the otherwise perfectly-functioning scrap chopper required tightening a couple of times a day, Steinbock had a flash of inspiration which he hastily scribbled down on the proverbial napkin. His solution worked perfectly, and the bolts never came loose again. Steinbock’s solution, to split one big
R
torque into a number of smaller torques, was commercialised as Superbolt. “He was actually surprised that nobody had thought of it before,” says his son, Allan Steinbock, who is the company’s vice- president. Word spread to customers beyond the steel industry and, today, Superbolt’s multi-jackbolt tensioners can be found in a wide range of applications, from satellites to submarines to the Large Hadron Collider at CERN. The problem Steinbock tackled is the
fact that for bolt diameters bigger than about M24, it is very difficult to create enough torque to tighten or loosen a bolt. Simple physics shows that the torque needed to properly pre-stress a bolt increases by the third power of the bolt diameter. Therefore as the bolt diameter increases, the torque requirement for tightening it soars. Traditionally this has required some
30 Fastener + Fixing Technology • Issue 5 Apr - Jun 2012
olf Steinbock’s eureka moment, which came in 1974 while on a service call to one of his scrap choppers in a US steel mill, solved at a stroke
Hall: 21 Stand: D31
Words: David Wiles Photo: Christer Ehrling, Superbolt & CERN
With Superbolt® customers can
tighten even the largest bolts with hand tools. Like the Nord-Lock product range, the result is safer, faster and more accurate bolting, making them a perfect match. Here Nord-Lock takes a closer look at it’s latest acquisition.
heavy-handed methods, but all have their drawbacks. The sledgehammer gives
little control, is inconsistent and often causes injuries. Thermal tightening, crane wrenching, hydraulic wrenching and hydraulic tensioning can be expensive, inaccurate, time consuming and unsafe. However, Superbolt tensioners, which
are designed as direct replacements for standard nuts and bolts, allow for the tightening of large bolts with simple hand tools, making bolting more accurate, faster and safer. “The primary benefit of Superbolt is the reduction of torque required,” says Steinbock. “You only need a handheld torque wrench or air tool.” Superbolt tensioners utilise a ring of
hardened jackbolts threaded into a nut body. The Superbolt tensioner is first threaded by hand onto a new or existing bolt or stud. Once positioned, bolt tensioning is accomplished by tightening the circle of jackbolts. A number of different product lines are based on the same basic concept. “Because we are able to generate the
proper preload, we achieve the proper holding power and we don’t have bolts or nuts coming loose, even in high-vibration situations,” says Steve Busalacchi, engineering manager. “This reduces expensive downtime: both downtime required for maintenance to retighten loose bolts, but also downtime caused by studs breaking due to insufficient holding power.” Because Superbolt can be installed
with hand tools, there are also time savings. “We install quicker and we remove quicker,” says Busalacchi. “People’s first impression is that it will take longer because they have several
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60