Products ODU Connectors
New stand-alone website for Mass Interconnect Interfaces Due to increased demand for their ODU-MAC® Black-Line connectors, ODU have launched a new stand-alone website to support test equipment OEM’s, by explaining their many interconnection options as clearly and quickly as possible. Mass interconnect systems are mainly used for testing printed circuit boards and electronically assembled components. So, what is important? Firstly, reliable measurements are ensured by ODU's well-proven contact technology. Equally important is the flexible configuration of interfaces, for which these modular connectors are ideally suited. If preferred, customers can have a customized total solution with everything from a single source, including cable assembly. Try it for yourself
Give the new website a test drive at:
www.odu-interconnect.com Engineering Design Show 12-13 October 2022 Coventry Arena We’ll be on stand K4 - why not stop by for a chat?
www.odu-uk.co.uk
Omron adds compact, high performance DC relays for automotive and mobility applications Three new PCB relays from Omron Electronic Components Europe target automotive and mobility applications where space is tight and high-performance is crucial. The new Omron G8K, G8G and G8PM relays support high-performance DC motor control with a floor size and volume that is up to 95% smaller than similar relays on the market. The devices are all smaller than standard DA relays and deliver high contact pressure
with maximum coil size combined with AC500V insulation capacity. Each device targets the specific needs of different motor control applications in a tiny format that favours high-density mounting, cutting overall PCB costs.
https://components.omron.com/eu-eu
Tell me about JTAG software! JTAG/boundary-scan software
How do you (as OEM) keep the quality and costs of your (outsourced) production under control in today’s miniaturization of electronics? Testing today’s electronics, where not all nets can be provided with test points, is becoming increasingly difficult or even impossible using traditional test methods. But the production chain also raises new questions. How do you keep track of what is being produced for you and what can you do, for example, to relieve your EMS partner and find solutions together? This process starts in the design phase of your electronics with the definition of a suitable test strategy. Already in this phase it is important to analyze which test methods can help you to achieve the desired quality and the associated fault coverage. This knowledge helps you to coordinate the test options with the manufacturer of your electronic assemblies.
Tools for the entire lifecyle The JTAG/boundary-scan capabilities present on a PCBA can be used throughout its entire lifecycle for various test and debug purposes.
Design and (field) service In design and (field) service the engineer needs to find the
cause of the failure present. Interactive software tools that make it simple to apply a stimulus or a sequence of stimuli to (a part of) the circuit and observe its response are ideal for this application. With JTAG/boundary-scan a basic connection of a TAP cable and power is all that’s required to start the interactive measurements. No further preparation is needed. Boundary-scan measurements are as simple as measurements with conventional instruments like multi-meters and oscilloscopes.
Production
While a design or service engineer may use interactive tools to perform measurements to find the cause for a failure present, the production engineer faces a completely different challenge.
In production it is not always known if one or more failures, or manufacturing defects, are present on the unit under test (UUT). Here the challenge is to build a series of tests, able to determine that none of the possible manufacturing defects are present on the target UUT. Interactive debug tools are no longer sufficient and automated test tools are also needed. Tools that can generate tests and accurate fault coverage reports as execute the tests automatically within a sequence.
Hardware Products Your JTAG/boundary-scan system is only as dependable as the interface hardware it runs on. Our JTAG controllers and auxiliary modules deliver high throughput and excellent signal integrity for consistent running in production environments.
JTAG Technologies For more than 25 years JTAG Technologies has been solving the quality needs for many companies worldwide. Every manufacturer has its own test challenges, what are yours? We would be happy to analyze the possibilities together with you. Let us take a look at the test coverage and the resulting quality of your products. Together we analyze lead times, costs and work out reasonable overall solutions.
Insulation Resistance and Dielectric Withstanding Voltage Testing
Insulation Resistance and Dielectric Withstanding Voltage are two qualification tests that most connector manufacturers perform house during part qualification testing. These tests are designed to ensure that when a connector is used in environmental conditions at the rated working voltage (de-rated from the test voltage) the product will not fail, and there will not be current leakage.
https://www2.samtec.com/electronics-world/enewsletter/ir-dwv- testing
36 September 2022
www.electronicsworld.co.uk Read more in depth For more in-depth information, download the white paper:
https://www.jtag.com/white-paper-tell-me-about-jtag-software?utm_source=magazine&utm_medium=ad&utm_campaign=lpjtaginsta_camp_electronicsworld_magazine_ad
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40
