MACHINE SAFETY
therefore advisable to apply the new requirements immediately, regardless of harmonization, as the MRL also references the state of the art.
WHERE, FOR EXAMPLE, ARE THE CHANGES IN THE
SYSTEMS SPECIFICALLY NOTICEABLE? Let us think about a classic in industrial plants: vertical safety light grids for access protection. In the previous version of the standards, 2 beam safety light grids were only permitted with a corresponding justification in the risk assessment. The use of these devices is now ruled out, as the distance between two beams has been limited to a maximum of 400mm in order to prevent climbing through. In addition, the value to prevent the light grid from creeping underneath has been reduced from 300 to 200mm. The value against climbing over remains unchanged at 900mm, but these factors mean that at least three-beam safety light grids must be used in future. Manufacturers and operators must pay attention to this when selecting the required safety technology - Leuze offers suitable solutions here with its multiple light beam safety devices in up to four-beam versions.
THE “REACHING UNDER” OF VERTICAL PROTECTIVE FIELDS HAS BEEN INCLUDED IN THE STANDARD.
DOES THIS INCREASE SYSTEM SAFETY? Definitely. The previous version of the standard did not actually take reaching under into account, only the value of a maximum of 300mm of the lowest beam above the reference plane. In this respect, you could easily reach under a protective field with one hand or arm. From now on, the reach for reaching underneath must be determined so that the safety light curtain, for example, can be installed correctly. The now reduced value against crawling under also increases safety.
YOU ALSO MENTIONED THE SUBJECT OF ACKNOWLEDGEMENT BUTTONS, WHICH IS NOW
COVERED COMPREHENSIVELY IN THE STANDARD. Correct, ISO 13855:2024 now explicitly addresses safety-related manual control devices - i.e. SRMCDs. The term is defined more broadly in the standard, but mainly relates to the installation position of acknowledgement buttons. In the past, it simply
One of the changes: a constant additional distance depending on detection capacity and mounting situation [mm].
stated “The reset device must not be accessible from the danger zone”. The distance to an SRMCD, and thus in particular for acknowledgement buttons, must now be calculated. The calculated values may also end the previous discussion as to whether something is unachievable.
THE CURRENT STANDARD ALSO INTRODUCES REQUIREMENTS FOR SAFETY DISTANCES IN
CONNECTION WITH STEPS. WHAT IS BEHIND THIS? All values in the standard for calculating the safety distance refer to a reference plane. This is often the floor on which the person is standing, but it does not necessarily have to be. If there are steps, accessible machine frames or platforms on a machine, this always leads to the question of which of the two levels is the correct reference level. This is now clarified in detail in the standard using several examples. The standard distinguishes between ascent and descent, step height and width and then uses a table to directly specify which surface is the reference level in order to avoid misjudgements.
THESE ARE JUST SOME OF THE CHANGES RESULTING FROM ISO 13855:2024. DO EXISTING SYSTEMS NOW HAVE TO BE ADAPTED?
At this point, it is important to distinguish between the manufacturer and the operator. In accordance with the Machinery Directive, the time of placing on the market always applies to the manufacturer. This means that old systems are not relevant for the manufacturer, but all newly built machines are and this applies equally to special machines and series machines. The operator is subject to the current Industrial Safety and Health regulations that require a risk assessment to be reviewed regularly. The state of the art must be taken into account and, where necessary, the safety technology must be adapted. The new version of the standard is state of the art and therefore also relevant for existing systems.
WHAT CAN MANUFACTURERS AND OPERATORS DO TO KNOW THE CURRENT STATE OF THE ART? CAN YOU PROVIDE SUPPORT HERE?
Sustainable machine safety begins with the professional planning of safety systems and extends over the entire life cycle of a machine. Leuze’s teams of experienced and certified experts offer the appropriate support here
Experience has shown that it is difficult to always know the current state of the art given the large number of standards and directives and their regular revision. And then also to evaluate the machines according to the state of the art. That is why we offer a wide range of services to provide both manufacturers and operators with the best possible support. From simple safety inspections and follow-up time measurements, the complete safety-related assessment of a machine park to the implementation of the safeguarding of a machine or system, including services and engineering, everything is included. We also recommend our practical online seminars, especially on the new ISO 13855:2024. Another tip for manufacturers and operators: the calculation tools at
www.leuze.com. These are extremely practical for determining the safety distances in accordance with standards. And for more complex applications, the Sensor People from Leuze are happy to provide individual advice and additional support in the selection of suitable sensor technology and safety solutions.
Leuze
www.leuze.com INDUSTRIAL COMPLIANCE |AUTUMN 2025 17
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36
