FEATURE PPE BREATHABILITY AND CLOTHING COMFORT


Personal protective equipment (PPE), as well as providing a physical barrier to hazards, needs to have breathability and comfort to allow the wearer to operate efficiently. Simulating differing environments helps assess materials used in clothing for leisure, sport and personal protection, as SATRA explains


C


omfortable clothing is important to us all. However, it is particularly critical to certain


sports, leisure and occupational activities where the characteristics of the clothing can seriously overburden the wearer, impairing performance in carrying out their activities. Many items of specialist clothing used as


personal protective equipment (PPE) are intended to provide a physical barrier to hazards. Foul weather clothing and firefighters’ suits for instance, need to exhibit good water vapour permeability and water penetration resistance to allow the wearer to continue to operate effectively. If these properties are absent or at low levels, the wearer is likely to become prematurely fatigued and only able to operate in hostile environments for limited periods. In addition, firefighters’ clothing with low water vapour permeability can lead to an increase in steam burns. SATRA has specialist laboratory facilities for


physiological assessments and associated test methods that enable a number of wearer comfort parameters to be quantified.


CLIMATIC CHAMBERS Ambient conditions have a major influence on a wearer’s perception of comfort of products such as clothing and footwear. Low ambient humidity aids the evaporation of moisture, which helps to keep us cool and clothes to dry out quickly; people experience far less discomfort and can endure higher temperatures at low humidity than in high humidity environments. Ambient temperature and humidity also can


have a significant effect on the strength and performance properties of many materials from which consumer products are made. This applies particularly to natural materials (for example cotton – which is stronger when wet – leather and wood) but also to man-made materials (hydrolysis of polyurethane, heat softening of plastics, weakening of adhesive bonds). SATRA has a range of climatic chambers that


enable us to simulate a wide range of moderate and extreme environments. The company’s most versatile chamber operates between -40°C and +40°C with humidity levels up to 99 per cent relative humidity. The room is big enough to comfortably accommodate several people or house a treadmill or large items of test equipment. The chamber’s internal temperature and humidity is continuously controlled and monitored. SATRA has two thermal imaging cameras which can be used to record temperature distribution over large areas at a glance. As well as recording annotated still


18 AUTUMN 2019 | INDUSTRIAL COMPLIANCE


images, SATRA can record thermal video of many subjects or dynamic changes in temperature.


ASSESSING PERMEABILITY OF WATER- RESISTANT BREATHABLE MATERIALS User comfort and reduced physiological stress have been significantly improved with the introduction of garments incorporating permeable membrane and other technologies. This means people can operate longer and more efficiently in adverse conditions. There are many tests for assessing water vapour


permeability but there are no generally agreed guidelines to allow realistic comparison between materials. This has meant it has been difficult for buyers to make comparisons when selecting garments. SATRA has carried out work to study the behaviour of various membranes, and has developed a treadmill evaluation protocol, where assessments are made of user comfort while monitoring the temperature and humidity within a standard base layer during the trial. Comfort questionnaires can also be administered to evaluate other design aspects of the garments. Another excellent test for analysing the


breathability of materials or assemblies of materials is SATRA TM47:2002 - ‘Water vapour permeability and absorption’. In this test, a clothing fabric assembly (outer material, membrane and lining) is sealed across the top of pots containing a measured amount of water. The pots sit in a warm water bath so that water vapour is generated below the fabric stretched across the pot opening. After a defined time the amount of moisture that has both permeated through the materials, and been absorbed into them, is determined. The results of this test correlate very well with the human wear trials – higher permeability results being obtained for materials found to be more comfortable when incorporated into products worn by test subjects. This test is now in routine use at SATRA and is proving a reliable means of classifying the performance of water resistant, permeable materials for clothing and can also be applied to gloves.


SWEATING GUARDED HOTPLATE The sweating guarded hotplate is used for measuring the thermal and water vapour resistance of sheet material. It is currently the approved method for assessing the performance of breathable and insulating materials for protective clothing in standards such as EN 343, EN 471 and EN 469. The device consists of a measuring unit and


thermal guard ring, which are fitted with heaters and temperature sensors. The top surfaces of the measuring unit and thermal guard ring are flat and level. The surface of the measuring unit is porous to allow water, at the same temperature as the measuring unit, to evaporate from the surface. The measuring unit incorporates a water reservoir. In operation, the plate and guard ring are mounted in an environmental chamber where the temperature and humidity are tightly controlled. The temperatures of the measuring unit and


thermal guard ring are controlled at 35°C ± 0.1°C in order to mimic the temperature of human skin and the test specimen is laid over the measuring unit and thermal guard ring so that it overlaps the thermal guard. The environmental chamber in which the instrument operates is set to 35°C for water vapour resistance measurements and to 20°C for thermal resistance measurements. The device operates in two modes: i) for


measuring water vapour resistance (or ‘Ret’), and ii) for measuring thermal resistance (or ‘Rct’). In the thermal test, no water is used. The operation of the device is, in principle very


simple. Initially SATRA runs the device without specimens and the bare plate constants for water vapour resistance or thermal resistance are calculated. With the test specimen in place, the plate and guard ring are controlled to the appropriate temperature. The device is allowed to settle down and achieve steady state in which the heat lost from the upper surface of the test specimen is equal to the heat input from the measuring unit. Once steady state conditions occur, the power (watts) required to maintain the steady state conditions over a period of time, is measured. The result for a particular material is the value obtained with the test specimen in place minus the bare plate constant. SATRA has installed two sweating guarded


hotplates. One is operated full-time in the Ret mode and the other operates in the Rct mode, which enables SATRA to turn this work around quickly and meet manufacturers’ deadlines. In addition to testing the breathability and


insulation of clothing materials, SATRA can carry out bespoke testing on a variety of other consumer products. For example, products recently assessed include insulated bags for the storage of medical devices, and medical dressings, which were evaluated to record the humidity levels beneath them when adhered to a simulated patient.


SATRA www.satra.com/ppe / INDUSTRIALCOMPLIANCE


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32