www.heatingandventilating.net
VENTILATION & HEAT RECOVERY
“The ventilation sector is welcoming the increased focus on competency within the updated guidance, recognising that good ventilation design will play an essential role in delivering energy-efficient, low-carbon homes.”
Training
At Vent-Axia we welcome the changes as we are committed to best practice and have been championing competency for over a decade, with the company running an NICEIC Domestic Ventilation Training Course at our Crawley training suite. Demand for the course has risen significantly, initially following Covid and then again with the launch of Awaab’s Law. The latest changes to Part F are set to drive a further uptake in the course. We are already prepared for this growth with a new training facility set to open at our Dudley manufacturing site in the coming months. The course meets the minimum technical
competency requirement for Installers looking to apply to join a Competent Person Scheme in England and Wales for Domestic Ventilation Systems and is also relevant for installers working in Scotland and Northern Ireland. The course has been designed to provide the
necessary skills in design, installation, testing, commissioning, handover, servicing and fault- finding of ventilation systems in accordance with the latest National Occupational Standards (NOS) and Minimum Technical Competency documents (MTC).
As well as good design and installation, selecting a high-performance ventilation system is essential to ensure adequate airflow and energy efficiency are achieved in practice. MVHR is the ideal solution since it provides healthy filtered air, supplying and extracting air continuously, while recovering heat that would be otherwise lost. To reduce carbon emissions, it is vital to select an MVHR with a low SFP in conjunction with a high heat recovery, but complete controllability is essential too, to maintain high levels of IAQ and comfort for occupants. Vent-Axia’s award-winning Lo-Carbon Sentinel Econiq MVHR range has been designed to meet these challenges with 93% heat recovery and complete controllability.
heating & plumbing solutions PH-3.8L-HW
3.8-LITRE PRV AND CONDENSATE PUMP
MAX. FLOW 312 LPH TANK CAP. 3.8L
DECIBEL RATING 53 dB(A) PUMP CYCLE 1.5L UP TO 2.8pH BOILER
• DEALS WITH BOILER CONDENSATE
handles up to 110°C
• HIGH PRESSURE AND PRESSURE RELIEF PUMP
8 6 4 2 0 150 300 450 CAPACITY (LPH)
This 3.8L pump has been designed to handle standard condensate and to instantly reduce the temperature of any PRV discharge. The pump is manufactured from high temperature plastic and higher specification hose. The pump has an extra large drink cycle of 1.5 litres suitable for boiler condensate and PRV discharge for boilers up to 42kw and boiler condensate only for boilers up to 600kW.
600
BOILER & HEATING SOLUTIONS
STAND 5F33 PH-5L-HW
HIGH TEMPERATURE AND PRESSURE RELIEF PUMP
MAX. FLOW 1200 LPH TANK CAP. 5L
INLET 25MM UP TO 32 LPM
• UNVENTED TEMPERATURE AND PRESSURE RELIEF
• SOLAR CYLINDER TEMPERATURE AND PRESSURE RELIEF
handles up to 100°C
6 8
4 2 0 500 1000 CAPACITY (LPH)
Manufactured in the UK this heavy-duty, high-temperature tank pump incorporates thermal overload protection and high-level alarm switch. Ideal for unvented cylinder T&P discharge and steam humidifiers. Having one of the largest discharge rates of 20 litres per minute, this pump can handle both high-temperature up to 100 degrees and high-flow rates.
DOWNLOAD THE HVR APP NOW pump-house-ltd pumphousepumps @pumphouseltd @PumpHouseLtd diversitechuk June 2026 21 1500 FOR UNVENTED T&P
METRES HEAD
METRES HEAD
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32
