PC-FEB24-PG44.1_Layout 1 31/01/2024 12:09 Page 44
SEALS & GASKETS
SEALS BUILT TO RESIST AGGRESSIVE ENVIRONMENTS
Dean Oliviero, managing director of EAP Seals, which recently became part of AFC Industries company TFC, explores some important considerations when designing a custom seal for use in demanding environments
B
y ensuring an airtight, watertight fit, rubber seals prevent unwanted leakage in components ranging from pumps
and valves to pipe fittings and vacuum seals. Achieving an impervious connection means carefully selecting the right seal according to the application and, sometimes, designing a custom part.
In many cases, manufacturers can opt for a standard, off-the-shelf seal. As well as being readily available, these products are certified to ISO 3601 standards and come with relatively low lead times and upfront costs because custom tooling is not required. However, exceptionally demanding or aggressive environments may require a bespoke option built from specialist materials that can withstand increased demands on temperature stability, chemical resistance or other factors. In these cases, manufacturers may need to commission or design a custom seal, selecting an appropriate material, surface finish and geometry for the requirements of the final application.
High temperature resistance When exposed to environments close to or beyond the recommended operating temperature, rubber seals and O-Rings can degrade and risk becoming non-functional. Excessive heat can lead to both swelling and hardening of the material, resulting in permanent deformation. Meanwhile, extreme cold temperatures can result in elastomer seals becoming harder and more brittle.
44 FEBRUARY 2024 | PROCESS & CONTROL
Many standard materials offer wide temperature ranges. For example, Nitrile rubber (NBR) can operate in environments ranging from -40 to +108˚C, and is resistant to oil, gas and petroleum-based hydraulic fluids. However, AFLAS is more widely used in the oil & gas market because of its ability to withstand temperatures of up to +250˚C.
treatment plants, methane can cause rubber to swell and crack
“ In wastewater
Another material with a wide temperature range is Viton (FKM/PPM), a fluoropolymer elastomer and hydrocarbon rubber with a working temperature range of -20 and +205˚C depending on the grade.
Chemical resistance According to the UK Government, occupational
exposure to hydrogen sulphide (H2S) is a significant risk for those working in oil, gas and petrochemical facilities. As well as the damaging impact on human health, these chemicals can cause the deterioration of engineered components.
When exposed to H2S, non-resistant elastomers become hard and brittle, losing their elastic properties and ability to seal effectively. Meanwhile, in wastewater
”
treatment plants, H2S and methane are both present, and methane can cause rubber to
soften, swell, crack and become brittle. Once again, AFLAS is a strong contender for these facilities because of its high resistance to acids, amines/bases and steam. Another option is seals made from perfluoroelastomer (FFKM/FFPM), as this material can resist chemicals including concentrated nitric acid, sodium hydroxide, ethylene diamine and steam.
Water resistance In water filtration systems, seals must be water resistant to avoid degradation due to oxidation. Usually, we’d recommend using EPDM rubber because, as a synthetic rubber comprised of ethylene, propylene and diene, it boasts excellent waterproofing properties. Meanwhile, if the seal will be exposed to external pressure and regularly stretched, a material with good tensile strength is required. Polyurethane materials would offer a better solution than most rubber alternatives for these applications because of their superior tensile strength and ability to withstand abrasion and wear.
With certain high-end polymers, demand outstripping supply has meant that lead times could still be up to a year. However, by working with an experienced seal and O-Ring specialist, manufacturers can access comparable perfluoroelastomers with better lead times and at a reduced price. TFC offers a wide range of O-Rings and Seals for applications ranging from oil & gas and automotive to food & beverage. It recently acquired EAP Seals, which means customers can now benefit from a seamless experience when ordering seals, springs, retaining rings or when streamlining their supply chain with TFC Vendor Managed Inventory (VMI).
TFC
www.tfc.eu.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58
