FEATURE LINEAR MOTION/MOTION CONTROL
MAKING THE UPGRADE FROM HYDRAULICS TO ELECTRIC LINEAR ACTUATORS
When upgrading from hydraulic designs to electric linear actuators, accurate sizing of the existing application is crucial to achieve the most efficient and cost-effective specification. Gerard Bush, engineer at INMOCO, explains
W
hile capable of achieving equivalent forces to hydraulic designs, electrical linear actuators offer a number of
benefits including precision and reliability. Today, electric linear actuators from a brand like Tolomatic are available in bore sizes up to 127mm (5”) and can exert up to 222.4kN (50,000lbf) of force. They can therefore handle force demands across virtually all applications – from metal presses to cranes – except for those requiring the very highest force, where hydraulic designs still have an advantage. When considering retrofitting an application, or
upgrading a machine design, reluctance to switch from hydraulic to electric is often a result of the perceived time and cost of the update. Long term though, it’s nearly always less expensive, and time saving, to make the change. Electric designs are almost maintenance-free
and their high reliability means significantly less downtime, which optimises application productivity. Furthermore, electric actuators are less expensive to run: while hydraulic systems only achieve around 50% efficiency, electric systems typically operate at 75-80%.
THROUGHPUT The improvements in precision and repeatable accuracy also mean that electric actuators can deliver a boost in throughput as well as production quality. The motion capabilities of an electric design enable real-time management over force, position and velocity, as well as acceleration and deceleration. This level of control also expands the functionality of what a machine can do. However, when converting an existing machine or design to electric actuators, accurate sizing is crucial. When conservative estimates are applied in place of confidence in accurate sizing, this usually delivers an oversized and overpriced actuator. The system pressure method of actuator sizing falls into this category, taking the area of the cylinder multiplied by the rated system pressure. To achieve accurate sizing, calculating the true peak and continuous working force of the
hydraulic cylinder is the optimum approach. This means identifying, as closely as possible, the forces acting on each side of the piston, then calculating the effective area of the rod side by subtracting the rod area from the full bore area. Finally, ensure that the actuator can deliver the required application force by considering the difference in force between the two sides.
“The motion
capabilities of an electric design enable
real-time management over force, position, velocity, as well as acceleration and deceleration”
ACCURATE SIZING
Recording the values of the application while in operation will achieve the most accurate data, and this requires a load cell or an electric actuator installed in the application. This method may not be possible with existing machines, so a practical alternative is to measure hydraulic pressures in the cylinder while the process is in operation. The closer the measurement is taken to the point of work, the more accurate the measurement, and this means measuring the pressure at the cylinder, which may be the least accessible. An alternative is to measure pressure between the valve and cylinder, as pressure- compensated flow controls and needle valves or other inline accessories downstream of the control valve may have an influence on pressure.
44 DESIGN SOLUTIONS NOVEMBER 2025
It’s also possible to measure the pressure at the
valve, and while this
is the most common for conversion applications, it’s the furthest distance from the work point. This can increase the error in actual versus measured pressures. However, even a pressure estimation within 15% of the actual force will provide a reasonable level of accuracy compared to the system pressure method.
SPECIFICATION SUPPORT Measuring the return pressure is also important. Usually, there will be minimal back pressure in the return lines, but some systems can have high return pressure between the cylinder and the valve that will impact the output force of the cylinder. The most accurate force calculations will also determine the dynamics on both the piston end and the rod end of the cylinder. When back pressure is applied to the rod end of a cylinder during an extend move, this will also offset some of the force applied to the piston end of the cylinder, and this must also be accounted for. Tolomatic provides a range of electric
actuators ideally suited to hydraulic replacement applications. These include the RSX extreme force actuator rated to 222kN force, through to the RSH hygienic actuators designed with IP69K protection for clean-in-place (CIP) applications. Supporting Tolomatic in the UK, INMOCO
can assist with hydraulic replacement projects including accurate electric linear actuator sizing.
INMOCO
https://inmoco.co.uk/
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
