DS-AUG26-PG20_Layout 1 20/07/2026 15:06 Page 1
FEATURE MACHINE BUILDING, FRAMEWORKS & SAFETY
MINIATURISATION IS RESHApING ENGINEERING
HOW Like the evolution from the bulky cassette-based Walkman to smartphones
Brushless motors from FAULHABER
I
n the last 20 years, we’ve seen huge cube-like TVs shrink to a centimetre thick, while terabytes of data can now sit on a chip
no bigger than a fingernail. And in industry we’re seeing smaller, lighter, more efficient systems. Miniaturising drive systems isn’t, however,
simply a matter of scaling down existing motor designs. It must carefully balance torque, power density, motor type and thermal management.
AccelerAting miniAturisAtion Medical devices such as minimally invasive surgical tools, diagnostic sensors and compact implantable systems require tiny, high- performance, components. Take, for example, robotic-assisted laparoscopic surgery. Here, miniature drive systems are used to actuate wristed end-effectors within instrument shafts often less than 10mm in diameter. These systems must deliver high torque
at low speeds to enable precise articulation, while maintaining minimal backlash and low inertia for accurate, repeatable motion. Thermal performance is tightly constrained because heat generated within the motor or gearbox must remain below thresholds that could affect surrounding tissue. As a result, the motor’s architecture, gear reduction, materials selection and thermal modelling become critical at the first point of design. In aerospace and automotive applications, every
gram of weight removed can contribute to greater fuel efficiency, reduced payload, and better design flexibility. Whereas in industrial automation, robotics and consumer electronics increasingly rely on compact motors and electronics to deliver power and precision in confined spaces. While each sector seeks different benefits of
miniaturisation, they all share the same set of pressures – limited space, demand for mobility or portability and a need for functionality without bulk. As a result, shrinking component size has become a strategic choice and designers are rethinking the architecture, materials and even manufacturing techniques to meet these demands.
0
that can store tens of thousands of songs, modern engineering also demands greater capability within dramatically reduced
physical footprints. Chris Handcock, technical manager at drive system supplier Electro Mechanical Systems, explores how
selecting the right solution
miniaturisation is changing product design To mitigate this, designers must address heat
But, small motors do not automatically deliver the same output as larger ones. To meet the same standards, engineers must carefully consider factors like torque output, power density, load-handling capability and energy efficiency. Smaller motors tend to have lower torque, meaning that designers may need to compensate with gearing, high-performance materials or alternative motor types. Here, selecting the correct micro motor
technology becomes critical. For example, coreless DC motors may suit applications where dynamic response and low inertia matter, such as medical or robotic systems. On the other hand, brushless DC motors, like those from FAULHABER, may provide a better balance of efficiency, lifespan and power-to- weight ratio for aerospace applications. Although they offer precise control,
stepper motors can be less efficient and more challenging to integrate at very small scales. In each case, motor type, winding geometry, magnet strength, gearheads, feedback systems and controls must be tuned to ensure performance without exceeding the constraints imposed by size.
Achieving precision Another engineering challenge that presents with miniaturisation is thermal management. As motors get smaller, they lose surface area relative to the amount of heat they generate. High power density in a compact space can lead to heat accumulation, which can degrade performance, reduce efficiency and damage components.
2 DESIGN SOLUTIONS 1971-2026 JULY/AUGUST 2026
as an integral part of the design process rather than as an afterthought. Solutions could include optimising magnetic materials, improving insulation, designing housings or airflow paths to aid heat dissipation, or embedding thermal sensors. In some cases, compact systems might incorporate heat-spreading housings, micro-cooling channels and other advanced thermal management features. Addressing these considerations at the start of
a concept is essential, as thermal limitations can dictate the performance envelope of a miniature motor. This is where precision manufacturing becomes crucial. Off-the-shelf motors and gear systems are often unable to meet the tight spatial, mechanical and performance constraints associated with tiny applications. For bespoke solutions, consider selecting
a partner such as EMS, which provides a comprehensive custom design and manufacturing service, from its UK based facility. Miniaturisation is reshaping engineering,
but consequently driving new expectations for performance, efficiency and design across every sector. Small, lightweight components now unlock capabilities that once seemed impossible. But real success demands more than shrinking hardware – it requires careful consideration of motor selection, uncompromised manufacturing precision and the support of custom design solutions.
EMS T: 0118 9817391
www.ems-limited.co.uk
www.designsolutionsmag.co.uk
sponsored by
Feature
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68
