Cases & enclosures H Hammond
hammondmfg.com T 38
COLOUR PRINTING ON ENCLOSURE COMPONENTS
he “Everything but the Enclosure” people at EMKA have made life a little bit easier for specialist enclosure and cabinet builders – they can now offer standard two-colour pad printing onto swinghandles, drawing pockets, air conditioning handles, drawer handles, L handles, T handles and even hinges as required. This service supports safety regulations, operation instructions and simple information provision to aid H&S goals – plus enhancing ease of operation, while it provides branding information for
service and operational needs. Typical print requirements include corporate presentation, e.g. logos etc., safety information, operational directions (pull, push, rotate, slide down, engage A before B etc.), also technical information e.g. 400VAC etc. or other design graphics to supply important points of operation data.
While two-colour printing is standard, more colours are possible to special request.
EMKA
www.emka.com
ammond has introduced the IP68 1550ZF range, flanged versions of all 18 sizes in the well-established 1550Z rugged thick wall heavy duty die-cast enclosure family. The full-size flange is spot-welded to the base to give a very strong and smooth mounting plate for use when the units are secured to a surface. The 18 sizes range from 50mm x 45mm x 30mm to 223mm x 147mm x 83 mm, with the lids thickness ranging from 5mm to 33mm in depth depending on the size. The tongue and groove design and a pre-formed one-piece silicone rubber gasket gives the IP68 environmental protection so the enclosures are ideal for installation in environments where dust and water will be present.
They are UL and cUL Listed and have been independently tested to IP66, IP67 and IP68 and they are also rated to NEMA Type 4, 4X, 12 and 13. All sizes except the smallest have an impact rating of IK08, defined in IEC 62262 as the equivalent to the impact of a 1.7kg mass dropped from 300mm above the impacted surface. Depending on the size, the lid is secured to the base with either two, four or six stainless steel Philips machine screws located outside the gasketed area, giving repeated access without degrading the environmental protection. They are available in a natural finish or with a tough polyester black powder finish to both the outside and inside of the enclosure. Clear areas in the painted versions are provided around the grounding points.
HEAVY DUTY FLANGED DIE-CAST ALUMINIUM ENCLOSURES
March 2025 Instrumentation Monthly
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84
