Flow, level & control
FLOW MEASUREMENT FOR WFI LOOPS
PREVENTING BIOFILM DEVELOPMENT
Within Water for Injection (WFI) loops, the potential for biofilm development is a critical threat that is primarily caused by laminar flow and the presence of dead zones in the pipework. Flow metering and control are crucial to prevent biofilm accumulation, and to achieve this, Surface Acoustic Wave (SAW) technology has significant advantages over traditional methods. Contactless, precision measurement and a straight measuring tube optimise hygiene while maintaining the critical flow rate. Bürkert’s business development manager for Pharma & Biotech, Damien Moran, explains.
A 36
s ultra purified water used in the preparation of parenteral drugs, it is essential for WFI to be free from impurities. To achieve this, a WFI loop is a closed distribution system that continuously circulates
the media, ensuring it remains within required specifications. However, a WFI loop alone cannot guarantee the quality of the output media. A key challenge is the prevention of biofilms, which are formed by the accumulation of trace bacteria. Undetectable, trace amounts of bacteria can enter a WFI loop through microscopic leaks or cracks in the system, or contamination from maintenance. Given the conditions necessary for their growth, including microscopic traces of nutrients, temperature fluctuations, or insufficient cleaning practices, this is how trace bacteria can develop into a biofilm. Precise flow control then becomes crucial to ensure that trace bacteria is not given the potential to grow.
BIOFILM DEVELOPMENT
Critical to this process is the prevention of dead zones, which are sections of piping with minimal or no flow. Stagnant water collated in dead zones allows bacteria to settle and multiply, while low flow areas, with less mechanical force to dislodge the bacteria, can also lead to bacteria accumulation. Microscopic physical imperfections within the WFI loop, including the piping and any instrumentation, can also harbour bacteria. Over time, as these bacteria develop into a biofilm, their removal is made more difficult when combined with insufficient flow.
The flow profile within a WFI loop must be turbulent to ensure an even distribution of water, whereas a laminar flow profile can lead to the
accumulation of bacteria. As a result, this means that flow velocity must be sufficiently high to ensure an adequate level of turbulence while maintaining optimum pump efficiency.
THE CHALLENGE FOR CORIOLIS METERS Traditionally, Coriolis sensor technology has been used within WFI loops to measure flow. A Coriolis sensor measures mass flow, and while this is useful for applications like precise dosing, the mass of highly purified water is uniform. Instead, the key measurements relative to preventing biofilm development include velocity and volumetric flow. However, the most significant challenge of a Coriolis sensor within WFI loops results from its design. The Coriolis effect is evident when a liquid interacts with a vibrating tube, and the liquid creates a measured twisting force; the higher the force, the higher the mass. A Coriolis meter typically integrates a bent tube because a curve enhances the twisting effect, which increases the precision of mass flow measurement. The curve also allows a longer path of measurement for a confined space.
DEAD ZONES
The problem is that the curves within a typical Coriolis meter can cause dead zones and low flow areas, which over time can lead to biofilm build-up. Moreover, the bends in the tube also cause a pressure drop. This decreases the flow and subsequently diminishes the potential of washing away trace bacteria before it can develop into a biofilm.
Pump speed could be raised to optimise flow, but this will increase energy demand and reduce the life of the pump, as well as raising the potential for maintenance. However, if pump speed becomes
too fast, this could also result in pressure drops. To manage pump speed, additional control technology could be integrated, but this will increase the cost and complexity of the design and add to the maintenance schedule. Crucially, bent tubes are more complex and time consuming to clean.
SURFACE ACOUSTIC WAVE TECHNOLOGY
An alternative flow measurement system for WFI loops is based on Surface Acoustic Wave (SAW) technology. With this approach, a flow meter generates surface acoustic waves that travel through the fluid. Calculating the time differences of the waves proportional to the flow, a SAW technology flow meter, like Bürkert’s Type 8098 FLOWave, can measure real time volumetric flow rate, cumulative volume, and flow velocity, as well as temperature – all vital indicators of conditions crucial to preventing biofilm development. The key advantage for WFI loop design is that SAW technology utilises a straight tube, preventing dead zones or the potential for pressure drop,
June 2025 Instrumentation Monthly
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76
