66 | Feature: Kallfass/Murray Timber Group
Above left: The stick sorter line – the robot can be seen in the background Above right: Installation of the new line began in June 2020
◄ “MTG wanted to have the machinery installed and they did everything to realise that,” said Matthias, adding that the pandemic didn’t hinder the early stages of the installation.
The Kallfass operatives on site included one mechanic (sometimes two), two electricians and, at the end of the year, one programmer – but Matthias stresses that they “had very good support” from the MTG team.
“It was very good to work together with them,” he said, adding that the company was always in step with Kallfass’s schedule and always ready for the next stage of the installation. However, at the end of the year it became more and more difficult for Kallfass to travel to Ireland and a lot of improvements had to be made via remote service.
“MTG had installed cameras at different points of the installation so it was possible for us to see what was happening, recommend adjustments and then to look back to see if they had helped,” said Matthias. “It also helped that the MTG team is very skilled technically and was able to describe issues and relay information very precisely.” The line has two entry points: one is from the old stacking line and marks the interface between the old and the new installations, where material is taken from the existing drop sorter in charges via an angle transfer and stacked with kiln sticks between the layers. The other entry point takes material from the kiln or from packages and is de-stacked, cut to length, stacked and strapped for post-processing.
The contents of a sorting box (the maximum wood length is 5.3m) are emptied in a batch onto a cross conveyor and fed to
TTJ | May/June 2021 |
www.ttjonline.com
a transfer point from where the batch is moved by 90O
to a subsequent step feeder.
After de-stacking the packs, (maximum size 1240mm wide x 1500mm high x 5300mm long) an inclined chain conveyor transports the layers further to a step feeder, where the sticks are processed via a belt conveyor and ejected into a belt deposit box.
Another step feeder splits each batch into portions which are then unscrambled and aligned on a common zero line. The operator visually assesses the timber and if end trimming is necessary, pulls the board up to 0.5m from the conveyor.
The boards are now fed layer by layer to the multiple cross-cutting saw, which is equipped with five variable positioned, pneumatically controlled chop saws. Two of the saw units can be pivoted by 30O
across the line and transported
scanner and damaged sticks are ejected. The sticks then move to the stick bundling part of the process where they are grouped into packs of 12. These are fed to buffer conveyors and, following alignment, Kallfass’s patented robot grabs the bundles and feeds them into eight double magazines. The automatic stick feeder is used for the sticks measuring 44x22mm that are used in the kilns. The smaller sticks (44x10mm and 35x10mm) used for timber packs ready to be dispatched are placed manually in a designated buffer conveyor from where the robot picks up the sticks and feeds the sticker magazines.
degrees.
The indirect drive allows boards to be sawn to a minimum length of 750 +/- 1mm. A maximum of 10 layers per minute are
stacked into packs. The packs are either taken from the front with the forklift, or transported to the strapping machine.
“If the material is going on into the kilns it doesn’t need to be strapped, but packs ready for dispatch will be strapped,” explained Matthias.
One of the main attractions of the new stacking line for MTG was Kallfass’s patented automatic stick feeding system with a performance of 80 sticks a minute. This is the first installation of its type in the UK and Ireland.
The stick bundles are placed with the forklift between the guide walls of the buffer conveyor and are then transported to the unscrambler. The separated sticks pass a
The strapping is equipped with two bearer magazines. The bearers are strapped together with the pack. A strapping cycle, including pack positioning, takes no longer than 18 seconds. The packs are taken off the subsequent angular transfer with a forklift. Matthias estimates that the line is running at around 90% capacity and says that as soon as Covid restrictions ease and international travel is allowed, Kallfass will return to the Ballygar mill to carry out some final fine-tuning.
MTG says it is very familiar with the Kallfass equipment and is very comfortable with it from a quality, design and performance point of view. “The big decision maker was the robot sticking machine, which was the solution we had been searching a long time to find,” said a spokesperson.
“It was perfect for what we wanted, fully automated, high performance and completely flexible as to where the sticks can be placed,” he continued. “We are very proud to have one.” ■
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85
