EXPERT COLUMN | LEEA
Technical Committee THE LEXICON OF LIFTING
Bernie Winter, from the Lifting Equipment Engineers Association (LEEA) Technical Services, runs through some of the commonly used lifting terminology.
to describe the lifting capacity of lifting equipment. As we all know, the industry has a bigger lexicon than those three terms, much of which is used throughout the LEEA COPSULE (Code of Practice for Safe Use of Lifting Equipment) that is the source of lifting best practice and can be downloaded for free at
leeaint.com/copsule. Being clear on what these terms
I
actually mean is important in an industry where risk of accidents is prevalent and the need for compliance with regulations is widespread. So let’s run through the key terms in the lifting lexicon. Current legislation uses the term
competent person for a variety of duties to describe a person with the necessary practical and theoretical knowledge, experience, training, skill and ability to perform the specific duty to which the requirement refers. So, there can be several competent persons, each with their own duties and responsibilities. A trained person actually using the equipment is usually referred to as an operative. When we talk about inspection to ensure
the safety of equipment, there are three levels: Pre-use inspection is normally completed by the operator of the equipment before each use and in accordance with the manufacturer’s instructions. Interim Inspection, also referred to as frequent inspection, focuses on critical components identified in the risk assessment (from which the nature and extent of the inspections is derived) that may become a danger before the next periodic thorough inspection (examination). The third level is a thorough examination, also known as periodic inspection or thorough inspection. This is a visual examination of the lifting equipment, carried out by a competent person carefully and critically and, where appropriate, supplemented by other means such as measurement and testing in order to check
20 | June 2024 |
www.hoistmagazine.com
recently wrote about whether Safe Working Load, Working Load Limit or Rated Capacity was the correct terminology
legislation, the term can include equipment that is intended to constitute an integral part of the load, and which is independently placed on the market. The minimum breaking or failure load is the specified load (mass or force) below which the item of equipment does not fail, either by fracture or distorting to such an extent that the load is released. The factor of safety is the ratio
between minimum breaking load and SWL, sometimes referred to in standards and legislation as the working coefficient, coefficient of utilisation or design factor. A proof or test load is a load (mass
Bernie Winter.
whether the equipment is safe to use. It is also used as a check of the suitability of the equipment and the inspection / maintenance regime.
Lifting equipment, also commonly
referred to as lifting devices, is a generic term to indicate loosely all lifting accessories and appliances. A lifting appliance is any machine that can raise, lower or suspend a load such as cranes, hoists, jacks, etc. However, the term excludes machines incorporating a guided load (such as lifts) and continuous mechanical handling devices (such as conveyors). Multipurpose equipment, usually referred
to as general purpose equipment in standards, is any equipment designed to a standard specification to lift a variety of loads up to the marked SWL. Used for multiple general purposes, it is not designed for one specific lifting application. Single purpose equipment or engineered lifting, is any equipment designed for and dedicated to lifting a specific load in a specified manner or working in a particular environment. Lifting accessory, or accessory for lifting, is used in current legislation to mean an item of equipment used to attach a load to a lifting appliance. Such equipment is also known as ‘rigging equipment’, ‘lifting gear’ or ‘lifting tackle’. In terms of supply
or force) applied by the competent person for the purpose of a test. This load appears on reports of thorough
examination, if a proof test has been made by the competent person in support of their examination, and on test certificates. Report of test, previously known as
‘test certificate’, is a report issued by the competent person who did the test and details the specifics of the test. Test reports are not legal documents allowing the equipment to be used, except when used in support of legal documents such as the Manufacturers Certificate or Report of Thorough Inspection/Examination. Verification is the generic term used
to describe the procedures adopted by the manufacturer or Competent Person to ensure that lifting equipment is to the required standard or specification, meets legal requirements and is safe to operate. This includes proof load tests, sample break tests, non-destructive tests, calculation, measurement and thorough examination. There is more on these terms and how
they are used in best practice in the free to download LEEA COPSULE. Being aware, and having an understanding, of this essential terminology will help you become fluent in the language of lifting and, critically, better able to carry out safer operations. For further information, download LEEA’s COPSULE at
leeaint.com/copsule or email
technicaladvice@leeaint.com.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69
