WATER MANAGEMENT If an operator fails to adequately
clean the basket strainers for any reason, both strainers can become clogged at the same time. This compromises the filtration process, resulting in quality issues or unexpected downtime until the problem is resolved. For many processors, this can occur simply due to having insufficient personnel to keep basket strainers clean along with their other duties. “As an alternative, a combination of
established complimentary technologies such as a macerator and an automated scraper strainer can essentially ‘knock out’ even the toughest problems related to large solids and high solids loading in an automated way,” says Robert Presser, vice president of Acme Engineering, a North American manufacturer of industrial self-cleaning strainers. The company is manufacturer of environmental controls and systems with integrated mechanical, electrical, and electronic capabilities. In this configuration, a macerator
would be installed upstream to reduce large solids down to a manageable size. The capabilities of the automated strainer are crucial to the process as well, according to Presser. “Although the macerator cuts up the
biggest solids, the strainer must still be able to separate both relatively large pieces and tiny particles while handling high solids loading without becoming obstructed,” he adds. In the case of Acme,
the OEM’s automated scraper strainer is designed to continually remove both very large and very small suspended solids from liquids and slurries. Cleaning is accomplished by a spring- loaded blade and brush system, managed by a fully- automatic control system.
A TRASH PUMP FOR ADDITIONAL PRESSURE If additional pressure is required to clean the screen, Acme Engineering can add an inexpensive trash pump to the blowdown line to assist in removing the solids from the strainer sump. “Since the solids are small, a little
trash pump can pressurise the blowdown line to evacuate solids from the strainer. The combination provides a decent ROI because operators no longer have to monitor and clean out heavily loaded basket strainers, resulting in substantially less labour and downtime,” says Presser. Alternatively, the sump can be
replaced by a cylinder bracketed by two gate valves that open and close as needed to remove the solids waste. “When you are ready to empty the
cylinder, you close the top gate valve momentarily and open the bottom one by depressing a button to dump the accumulated solids into a receptacle like a dump truck or a conveyor bucket so there is no manual handling required,” says Presser. According to Presser, Acme has
already worked with power plant operators and managers to implement a wide range of specialised straining systems for difficult applications with exceptionally large solids or very high solids loading.
BOILER WATER SLAG One example of this is boiler water slag. Over time, boilers accumulate ash that forms slag deposits, which act as insulation on the boiler tubes. Consequently, more fuel is needed to achieve the desired temperature and output compared with a clean boiler. By removing slag deposits, boiler efficiency can be improved by 1-4%, leading to reduced emissions from
Top: Acme Strainers fuel oil strainer Bottom: Acme Strainers steam jacketed unit for viscous fluids
power plants owing to decreased fuel consumption. For one power plant, Acme Engineering
addressed the slag issue by employing large cylinders and gate valves to strain out slag from a waste slurry produced during boiler washouts. The size of the cylinders used exceeded typical dimensions, with the largest cylinder measuring six feet tall and 18 inches wide. In another application, the OEM
employed a strainer, cylinder, and gate valve configuration to eliminate solid impurities and debris from Bunker C fuel oil. According to Presser, adapting
strainers for the specialised filtration of uncommon liquids and slurries requires not only expertise but also collaboration with the processor. “For unusual applications, it may take
a few attempts to get it right. You may have to adjust the timing and frequency of cleaning as well as adjust the screen slot size. There are quite a few variables involved,” he concludes. ●
For more information visit
https://www.acmeprod.com/ strainers
www.engineerlive.com 33
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
