SUBSEA TECHNOLOGY
AUTOMATING TESTING A
These subsea units shave days off testing times and eliminate human error from the monitoring process, explains Cynthia Pikaar
ccording to World Ocean Review, around one third of oil & gas reserves worldwide are extracted from off shore
sources. To reach these underwater oil & gas fi elds, specialised equipment is needed. However, repairs and interventions with subsea appliances quickly become costly. It is therefore vital that the electrical assets of subsea testing are regularly monitored. A common reason subsea electrical
systems fail is water ingress into the system. For subsea umbilicals, electrical integrity damage can occur anytime during their lifetime. C-Kore’s subsea testing tools, the
C-Kore Cable Monitor and the C-Kore Subsea TDR allow the installation or IRM contractor to quickly check the electrical integrity of subsea umbilicals. The Cable Monitor checks the insulation resistance and continuity of the electrical lines while the Subsea TDR unit looks for anomalies along the electrical lines by sending out a pulse and listening for the refl ections, much like a radar. By knowing how long the refl ections
take to get back to the source, the distance to the anomaly can be calculated, which can dictate the repair (or indeed replacement) scenario for the operator. The units are pre-programmed to run a specifi c test routine, which
The C-Kore product portfolio
typically only takes a few minutes. The information is then data logged and captured by the ROV’s camera. With the Cable Monitor readings the individual electrical lines can quickly be determined to be ‘good’ or ‘bad’, while the Subsea TDR determines where along the line the anomaly is. These values can be downloaded later into reports and graphs, easily documenting the testing results. Because the units are autonomous,
they do not require a specialised C-Kore engineer to accompany them off shore – a signifi cant cost saving for off shore campaigns. By plugging directly into the umbilical and automating the testing process, the results are quick, accurate and repeatable. C-Kore also provides remote data
analysis support. Some customers have said they have saved days of testing on their off shore mobilisations. The units all contain wet-mate
ROV operators observing C-Kore equipment from the control room
connectors, which allow easy connection into the system to be tested, either on-land or subsea. They can be
48
www.engineerlive.com
installed on the umbilical while it is still on the vessel, or they can be installed once the umbilical is on the seabed. This level of fl exibility is possible
because of the research done prior to installation. The C-Kore team talks to the engineers to understand the system, the connectors that are required, and the testing they want to accomplish. The experts then programme the units prior to dispatch. A test routine is run on either a set schedule or by activating the units via the light or proximity sensor. C-Kore will continue developing its
products based on operator needs. Its latest tool, the Subsea Optical TDR, allows operators to test the optical fi bres in umbilicals while they are subsea. The new tool is attracting attention from operators the world over, already being deployed in both the Gulf of Mexico and the North Sea.
Cynthia Pikaar is with C-Kore.
www.c-kore.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56
