HEATING, VENTILATION & SERVICES 59
which is effective and space saving; the round pipe, which offers improved flow rates but can be problematic where space is at a premium; the low cost flexible hose; and the latest addition – the radial. Radial ducting is specifically designed
T
for use with continuous mechanical venti- lation systems. Unlike traditional branch style ducting, radial uses 75 mm semi rigid ducting to connect directly from each room vent to a central distribution system, negating the need for various duct bends and connectors. This system benefits from less air leakage and improved air flow, which also makes for easier commissioning and a quieter system, as well as it being quicker to install than traditional branch ducting. Other ducting systems come in a variety
of sizes, and can be used for whole house ventilation or just for bespoke ventilation in the kitchen and bathroom.
WHICH TYPE IS SUITABLE? Which duct type you use may vary accord- ing to the ventilation system specified, and be further dictated by the installation requirements. For example, best practice, in accordance with the latest Building Regulations, states differing uses of the low-cost flexible hose depending on if you are installing singular axial fans, or an MVHR system. Nevertheless, flexible duct should always be pulled taught to ensure that the full internal diameter is obtained and flow resistance minimised. Whatever type you do opt for, one thing
that is universal is that you should choose good quality ducting. Substandard ducting could result in the ventilation system not meeting Building Regulations, through to a room with an ugly stain in need of redecoration as a result of leakage from the ducting system.
IDENTIFYING GOOD FROM BAD Sadly, there’s no standard to look for to help differentiate between products or ranges. Ducting that has been designed to work in harmony as part of a system and has been third party tested for end-to-end system performance is a very good start- ing point. Such rigorous testing guarantees the system will meet the required level of extract performance dictated by Building Regulations (Approved Document F). Exacting tolerances, i.e. the fit of rigid extruded systems, is a sure indicator of quality. If the channel or pipe bows or looks like it is concave, or the wall thick- ness appears uneven, the tolerances will be too wide. This is a problem because these systems are designed to push fit. If
here are four types of plastic venti- lation ducting systems to choose from: the original flat channel,
DEMYSTIFYING VENTILATION
With the growth of whole house ventilation systems, ducting products, and systems abound, specifying and installing them has become considerably more complex. Penny Jones of Domus Ventilation answers specifiers’ commonly asked questions when it comes to domestic ventilation ducting.
they don’t retain their shape, they can be difficult to fit together, but more impor- tantly they result in air loss, which reduces the system efficiency and increases the risk of moisture leakage around the connections – which can cause staining and damage to surfaces below.
ARE ACCESSORIES IMPORTANT? It’s important to consider not just the straight ducting available but also all of the accessories that you need to create the ventilation system as a whole, including moulded fittings and a range of bends from 90-45º. Having a wide range allows for a variety of solutions to individual problems. It gives you the ability to specify the ducting system in the most economic and aerodynamically efficient manner if, for whatever reason, you cannot meet the designed layout due to unforeseen site circumstances.
QUIET SYSTEMS A noisy ventilation system is more often than not a result of ducting that is too small for the volume of air extracted, or poorly installed. This creates excess noise and added strain on the motor and reduces life expectancy of the fan. Where the ducting isn’t the cause of
sound, it can be the carrier of it. Sound can travel down the ducting from the fan, or from traffic noise or room-to-room- cross talk. Duct sound attenuators can be used, which effectively absorb sound over a range of audible frequencies.
INSULATION Ducting insulation is required to meet Building Regulation requirements, as outlined in the Government’s 2010 Domestic Ventilation Compliance Guide. The Guide states that ducting must be insulated where it passes through
unheated areas and voids – such as loft spaces – to reduce the possibility of condensation forming, which can lead to unsightly and unhealthy mould. The Guide sets a minimum duct
insulation standard, which is the equivalent of at least 25 mm of a material having a thermal conductivity of ≤0.04W/(m.K). Domestic duct insulation products on the market are often unable to meet this requirement, so it is important to search for ones that can.
FIRE SAFETY PRECAUTIONS When a hole is made in a compartment wall for plastic ventilation ducting to pass through, the hole must be firestopped to restore the walls fire rating in accordance with Approved Document B of the UK Building Regulations. It is essential that the firestopping product you use for this has been specifically designed for this purpose.
Penny Jones is product and marketing manager at Domus Ventilation
WWW.HBDONLINE.CO.UK
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76
