DNM500 II Quick Specs Features
Š Fanuc 0i-MD Control with USB Port Š Direct Drive 12,000 RPM spindle Powerful 18.5kW (25hp) spindle motor OR
Š Belt Drive 8,000 RPM spindle Powerful 15kW (20hp) Spindle Motor
Š 10.4” Color LCD display Š Cartridge spindle design Š Air thru - spindle Š Big plus spindle System Š High precision spindle with 4 angular contact bearings Š Spindle orientation Š Spindle speed override 10 – 150% Š Rigid tapping Š Custom Macro B (User Definable) Š Cam Type Double Arm ATC 30 Tools Š Portable Manual pulse generator Š Program and data protection key switch Š Massive One-piece Meehanite cast iron Š Probe Ready(NEW) Š Doosan OP Panel (NEW) Š Large Linear Roller Guides (Y, Z 45mm / X 35mm) Š Servo motors mounted directly to the Oversized ball screws (X, Y and Z, 40mm)
Š Double Pre-tensioned ball screws Š AI APC (Mold / Die Software/ 20 block Look Ahead) Š Fast 36m (1,417 IPM) Rapid Traverse rate Š Metered piston distributor lubrication Š Telescopic covers Š Screw conveyors on both troughs for chip disposal Š Full enclosure splash guard Š Flood coolant with large separate coolant tank Š Work light Š Oil Skimmer Š 3 color tower signal light
Specifications Capacity:
Spindle:
X / Y / Z axis travel 1020mm (40.0”) / 540mm (21.2”) / 510mm (20.1”) Table loading area 1200mm x 540mm (47.2 x 21.2”) Allowable table load
800kg (1,764lbs.)
Table T - slot spacing x width (4) – 125mm x 18H8 (4.92” x .71”) Spindle nose to table top
Column to spindle center Big Plus Spindle System Speed 12,000 RPM AC Spindle Motor Acc./Dec time OR
Speed 8000 RPM AC Spindle Motor
ATC: Number of Tools 30
150mm to 660mm (5.9 to 26”) 587mm (23”) ISO No. 40
Torque (15min) 18.5Kw (25 HP)
15kW (20HP) Tool Shank
Pull Stud (retention knob supply company #) Motion:
X and Y axis rapid traverse rate Z axis rapid traverse rate Cutting feed rate
Least command increment
X and Y axis feed thrust (cont/inter) Z axis feed thrust (cont/inter)
* Positioning accuracy (full stroke) Repeatability
General: (12K Spindle) Machine Height & Weight Machine Height & Weight Utility: Tank Capacity: Voltage req’d - Fanuc
Coolant 380L. (100gal.) Air Required
2950mm (116.14”) & 6500kg (14,330 lbs.)
Floor Space Required (W x D) 3135mm x 2444mm (123.4”x96.2”) (8K Spindle)
2700mm (106.3’’) & 6500kg (14,330 lbs.)
Floor Space Required (W x D) 3400mm x 2250mm (134”x89”) Power req’d
34 KVA / 100 amp @ 220v 205-235 Volts / 3 Phase
Lubrication 1.4L (0.37gal.) Mpa .54(80psi)*250(8.83CFM)
* Accuracy data in the specifications are measured using KSB4207 * Geometric accuracies are guaranteed only if machine is installed on foundation meeting the minimum requirements of the machine.
Contact Doosan Infracore for the current machine requirements 117Nm (86 Ft-lbs.)
0 -12K (2.16Sec) 12K - 0 (2.21Sec.) Torque (15min)
210Nm (154 Ft-lbs.)
CAT 40 711-23
Max. Tool Dia. / Adjacent pots are empty 80mm / 125mm (3.15” / 4.9”) Max. Tool Length & Weight
30m (1,181 IPM)
1-15,000mm (.04 - 590 IPM) .001mm (. 0001”) 1,034 / 1,655 lbs. 2,257 / 3,611 lbs.
+/- .005mm (+/- .0002”) +/- .002mm (+/- .000080”)
300mm (11.8”) & 8kg (17.6 lbs.) 36m (1,417 IPM)
Contact Email:
dia.sales@
doosan.com www.doosaninfracore.com/machinetools
Midwestern Technical Center
1701 F Howard Street, Elk Grove Village, IL 60007, USA Tel. +1 847 437 1010
Fax. +1 847 437 1299
Corporate Office & Engineering Center
19A Chapin Road, Pine Brook, NJ 07058, USA Tel. +1 973 618 2500
Fax. +1 973 618 2501 Western Technical Center
488 W. Meats Avenue, Orange, CA 92865 Tel. +1 714 974 1330
Fax. +1 714 974 5296 Design and specifications are subject to change without prior notice - DIA121113
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140