ROPE
AND CORDAGE
WEBBING
PERSONAL GEAR
HARDWARE
SOLUTIONS AND KIT S
PATIENT CARE
LOGIST ICS AND SUPPORT GEAR
ANCHORAGE CONNECTORS
TERRADAP TOR™ WINCH SYS TEM
The new SMC TerrAdaptor™ TerrAdaptor™
Capstan Winch System mounts on any grey leg tube section in any position on the
multi pod. A stainless steel rope guide ensures that the rope enters the capstan at the correct angle for the greatest grip. Clip points on the front and rear of the bracket can be used for progress capture devices such as a rope grab or a prussik.
Key Features: Made from anodized aluminum • Includes a Harken 40.2ST two speed, self-trailing capstan winch • Stainless steel rope guide • Designed to work with progress capture devices • Engineered TerrAdaptor™
bracket • Made in the USA Height: 5.40” (13.7 cm) » Width: 5.90” (15.0 cm) » Length: 11.25” (28.6 cm) » Weight: 8.55 lbs (3.878 kg)
SM230552 $1,850.00 USA MADE TERRADAP TOR™ . CAP S TAN WINCH BRACKE T
The new Capstan Winch Bracket is designed for use with the Harken 40.2ST Capstan Winch. This bracket is predrilled and includes all hardware for mounting the Capstan. It may be mounted on any grey leg tube section on the TerrAdaptor™
Key Features: Stainless rope guide ensures rope enters capstan at the correct angle • Clip points are included for use of progress capture devices • Anodized Aluminum • Made in the USA
Height: 2.40” (6.1 cm) » Width: 5.90” (15.0 cm) » Length: 11.25” (28.6 cm) » Weight: 3.55 lbs (1.610 kg)
SM230551 USA MADE $145.00 USA MADE TERRADAP TOR™ S TANDARD WINCH BRACKET
The new Standard Winch Bracket is pre-tapped for mounting most Tractel and DBI/Sala cable work winches. In addition, other cable or rope winch models can be mounted per the manufacturer’s instructions. It may be mounted on any grey leg tube section on the TerrAdaptor™
.
Key Features: Clip points are included for use of progress capture devices • Anodized Aluminum • Made in the USA
Height: 2.40” (6.1 cm) » Width: 3.50” (8.9 cm) » Length: 11.25” (28.6 cm) » Weight: 3.06 lbs (1.379 kg)
SM230550 $102.00 winch
SHEAVE AS SEMBLY The TerrAdaptor™
Cable Sheave Assembly
is specifically designed for use with the TerrAdaptor™ TerrAdaptor™
Portable Anchor System and the Cable Winch Bracket that allows
you to utilize many of the commonly used cable winch systems. This Cable Sheave is a seamless connector maintaining the NFPA strength ratings while used in the multiple NFPA TerrAdaptor™ certified configurations.
NOTE: While this sheave may be used with either rope OR cable, it should not be used interchangeably. Once cable has been run through the sheave, it should not be used for rope.
Key Features: Zinc Plated Hardened Alloy Steel Sealed Ball Bearings • Supports up to 1/2” diameter cable or rope • Compact and easy to use • Made in the USA
Steel Sheave Assembly Weight: 4.2 oz (118 g)
SM230360 USA MADE
The TerrAdaptor™ Sheave Assembly fits directly on to the main attachment pin to act as a pulley.
BOLT REPLACEMENT KI T 4 Nylok Nuts Key Features: 4 SHCS Alloy Bolts • 4 Nylok Nuts
SM230326 USA MADE $4.60
LASH RING KIT SM230230
USA MADE $38.00
QUICKLASH The TerrAdaptor™
to work exclusively on the TerrAdaptor™
QuickLash has been designed grey
tube as an anchor point. With the QuickLash, TerrAdaptor™
users will now be able to install
an auxiliary anchor point before, during or after set up. Simply connect the QuickLash by inserting the quick release pin and you have a high strength single or multi direction tieback. This new QuickLash is ideal for attaching pulleys
or other gear to assist with tie backs, redirects, and/or tie downs. Quick, easy and high strength make this TerrAdaptor™ teams who have come to love the TerrAdaptor™
Key Features: Attach to grey tubes before, during or after setting up TerrAdaptor™
attached inside of leg and used to tie TerrAdaptor™
accessory a must have for all rescue .
• Connection point for single or multi direction tieback • Can be down for stability • Can be
used as attachment point for hanging pulleys or other gear • Can be attached at the foot connection point • 30 kN strength when loaded straight along major axis • 15 kN when strength when pulled to side at 90 degrees
MBS: 30 kN (6744 lbf) » Major Axis: 30 kN (6744 lbf) » Minor Axis: 15 kN (3372 lbf) » Weight: 4.2 oz (118 g)
SM230370 USA MADE $53.50
REPLACEMENT ROPE HOBBLE SM230307
$16.90 USA MADE $45.00
HARDWARE
ANCHORAGE CONNECTORS
81
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116