FEATURE PRECISION ENGINEERING Photo-Etching: Stimulating innovation in precision metal manufacturing
For over 50 years, Precision Micro has pioneered photo-etching, a manufacturing technology using subtractive chemical erosion to produce burr- and stress-free precision metal components. The company uses a 2-D process to create 3-D components that cannot be created with other technologies. Here’s more on the capabilities
T
here are teams of engineers in many OEMs grappling with the manufacture of new products and applications who will be asking themselves the question: “which metal fabricating process is the best fit for our requirements?”. The answer is not always straight forward, as the geometries of the part to be manufactured will vary, and so will the best fit manufacturing technology. Choosing the right fabricating technology will be affected not only by the type of metal being processed, but also by its thickness, the required quality of cut, and the speed with which the manufacturing operation needs to be completed. Ultimately, however, there are some givens
when it comes to process selection. Cost per part and quality are key and fairly universal drivers, and the customer is judge and jury when assessing the success of the manufacturing technology finally selected. When benchmarking technologies that are able to produce “precision” metal parts, most people consider that the viable alternatives are photo-etching, stamping, punching, and laser cutting. The unique characteristics of photo- etching overcome many of the issues associated with all of these more traditional metal cutting technologies, and as such — in some instances — when looking for a cost- effective solution for the manufacture of precise metal parts, it is the only viable choice. Photo-etching is a metal processing
8 SUMMER 2015 | MICROMATTERS
technology that produces stress free, flat, components by selective etching through a photo-resist mask. It is especially well suited to the manufacture of precision parts such as grids and meshes, lead frames for integrated circuit boards, fuel cell and heat exchanger plates, precision springs, washers and gaskets and decorative parts such as automotive interior trim.
THE ADVANTAGES When compared with conventional production processes, it has a number of inherent advantages, key among which are the ability to produce parts without degrading material properties, the fact that there is almost no limit on part complexity, and the ability to process a huge range of metals and alloys. Metals suitable for etching can be both ferrous and non-ferrous, and include austenitic and martensitic steels, coppers, brass and nickels. Hard to machine metals such as titanium and its alloys, and aluminiums can be processed, and also high temperature alloys such as Inconel, and precious metals including silver can also be machined. When looking at conventional processing technologies, each suffers from a number of drawbacks, key among which is the degradation of the material being processed due to high impact, or in the case of laser cutting the use of intense heat. However, the other key differentiator is in the area of
Figure 1:
Photo etching has the ability to produce finer detail than is possible with stamping
tooling, which can be illustrated by comparing photo-etching to stamping. The tooling for photo-etching is digital, so there is no need to start cutting expensive and difficult to adapt steel moulds. This means that large quantities of products can be reproduced with absolutely zero tool wear, ensuring that the first and millionth part produced are precisely the same. Also, as the tooling is “virtual”, it can be adapted and changed extremely quickly and economically, making it ideally suited for anything from prototype runs to high volume production runs. This allows for design optimisation without financial penalty, and helps ensure a low risk entry strategy as well as facilitating easy product updating. Turnaround time using phototools is about 90% less than that for stamped parts. Stamping requires substantial investment in mould fabrication which is not only costly but in some instances can take from six to ten months to complete, compared with a few hours for etching. The economy and adaptability of the tooling for photo-etching is a key stimulus to design freedom, along with the ability to produce what may seem like impossibly complicated products. As the cost of creating prototypes is so low there is no barrier to entry with the technology, with complex designs being produced in a matter of days and designs iterations in a few hours. Photo-etching opens the door for innovation, and pushes back the barriers that constrain many design engineers and allows for the manufacture of parts many thought impossible. Photo etching has the ability to produce finer detail than is possible with stamping, and all with minimal if any degradation and deformation of the metal being processed, and little to no likelihood of burrs or defects. Failure rates are minute, and unlike in the stamping process, every part produced is absolutely flat, which in some application is absolutely vital. However, stamping does have its place.
Whereas photo etching’s “sweet spot” is in the manufacture of complex parts in small to medium sized production runs, in extremely high volume runs where the tooling expense is justifiable, and where designs are not overly complex, stamping typically represents a more economic process. In essence, stamping fabricates a product by
pressing a substrate into a mould, and forming a certain shape while sequentially transferring the substrate using a sequential transfer press moulding device. Photo etching is an altogether more complicated process, hence its ability to be applied to complex geometries and to achieve exacting levels of precision.
Precision Micro
www.precisionmicro.com 0121 380 0100
/ MICROMATTERS
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36