STERILE PROCESSING INSIGHTS
Testing Scissors- Part 2
by Stephen M. Kovach Q A
September’s edition asked: “One of my fellow workers will not use the
non-latex material to test scissors. Instead, they use gauze. Is that acceptable?”
Let’s continue.
My assumption is your department might not have a written policy on testing scissors, which may be why your colleague is testing with something differ- ent than latex (artifi cial elastomer) material over gauze (an International Standards Organization [ISO] Standard). I found many statements inferring the use of latex as a test method back to 1990. Under the “Inspecting/Testing” section called “Scissors: Check sharps for smooth edges,” it states, “Check blades for nicks and smooth blade function. Check for loose screws. Test cutting ability by using a material that imitates human tissue quali- ties. The scissors should cut evenly all the way through the material.”1
“Cut through a latex sheet with 3/4 of the blade. Latex provides slight resistance to simulate what your scissors would nor- mally be cutting through. Make your ini- tial cut with about 3/4 of the blade, leaving the 1/4 of the blade closest to your fi ngers off the latex.”2 In a program given by Storz on scis- sors, they say “sharp instruments (scis- sors, rongeurs, osteotomes, curettes, knives) should be tested for sharpness and smooth cutting under magnifi ca- tion.” They also state many facilities use TheraBand (e.g., exercise bands) to test sharpness of Mayo and Metzenbaum (“Metz”) scissors. “There are two thick- nesses: one for scissors with blades longer than 5 inches, and one for scissors with blades less than 5 inches.”3 ASTM International’s Designation: F1079
– 87 (2017/R2022) standard supports using many different test materials (e.g., gauze, latex, etc.). “6.2 Cutting Ability—The test material shall comply with the material specifi ed in Table 1, Table 2, or Table 3. Clean scissors to be tested prior to testing. … Any bending or snagging of the test
material anywhere along the cut, including the distal tips, shall be cause for rejection.”4 Those three tables list all test materials highlighted in this two-part article. I believe one reason for switching to a latex-type material was to reduce lint caused by gauze. Many different origi- nal equipment manufacturers’ (OEMs) instructions for use (IFU) give little to no direction on how to test the cutting edge. Rather, they focus on inspection.5 Personally, a department needs a general enough statement to cover all situations based on what I have presented. Some possible wording for a standard operat- ing procedure (SOP) statement for testing scissors for sharpness is “As part of our functionality testing process, the various scissors in the department will be tested for sharpness (cutting edge) based on the review of the IFUs, standards, guidelines, and various technical literature on what materials (i.e., latex, non-latex, gauze, cot- ton balls, other material, etc.) should be used for testing the cutting edge of the medical devices.”
Also cite in the SOP’s footnotes the ASTM and ISO standards and various OEM IFUs of your department’s purchased scissors (Fig. 1). My suggested statement allows for this based on the informa- tion presented. It is important to review the IFU(s) in your department. Follow them concerning
SUBMIT YOUR QUESTIONS:
editor@hpnonline.com
testing your scissors for sharpness and adapt them to your practice. Consider this: if the IFU states to use gauze (and you are not using gauze), how do you justify using something else to test your scissors? And if the source of your latex material does not give any reference, how do you know it can be used and justi- fi ed if/when asked for by any surveyor? The AKI “Red Book” says, “As surgical
instruments are made for specifi c applica- tion purposes, the functional tests must be carried out so that items that fail to serve their intended purpose are reliably recog- nized and discarded. If in doubt, consult the instrument manufacturer for suitable testing methods.”6
This statement is a good
summary for this two-part article. I would purchase both the ISO and
ASTM standards and review them for proper SOP documentation. You will now have the “Why,” to back up using gauze, latex-type, and/or other material in your department for testing scissors for sharpness.
Therefore, medical device reprocessing professionals need to make sure scissors (no matter the type) are clean and func- tional when placed in the tray. This means various scissors can functionally cut (per the different testing methods and refer- ences for use). Being from Motown, I say know why “the way you do the things you do,”7 testing scissors for sharpness. HPN
when
References: 1. V. Mueller Division. (1990). V. Mueller Atlas of Surgical Instrument Care: A comprehensive program for cleaning and sterilization of surgical instruments. Baxter Healthcare Corporation.
2. Madden, H. (2021). How to Test the Sharpness of Scissors. wikiHow. Retrieved June 7, 2023, from
https://www.wikihow. com/Test-the-Sharpness-of-Scissors.
3. Bausch & Lomb Incorporated. (2023). Bausch & Lomb Storz Ophthalmics Continuing Education. Bausch & Lomb Storz Ophthalmic Instruments.
www.StorzOphthalmicCE.com.
4. ASTM International. (2017/R2022). Designation: F1079 – 87 (Reapproved 2022) Standard Specifi cation for Inserted and Non-inserted Surgical Scis- sors. [Section 6.2 Cutting Abil- ity, p. 1–2]. Formerly known as American Society for Testing and Materials (ASTM).
5. INTEGRA (2022, February). Surgical Instruments Indications for Use (KA202304) [JL-00032 Rev F. 2022-02 1486569-3]. Integra LifeSciences Production Corporation. Integra_LifeScienc- es_Surgical_Instruments_ JL_00032_rF_202202.pdf.
6. AKI – Working Group In- strument Reprocessing. (2017). Instrument Reprocessing: Repro- cessing of Instruments to Retain Value [aka “Red Book”]. (11th ed.) p. 50.
www.a-k-i.org.
Figure 1: Various purchased scissors found in one department. 42 October 2023 • HEALTHCARE PURCHASING NEWS •
hpnonline.com
7. Temptations, The. (1999). The Way You Do the Things You Do [Song]. On Meet the Temptations. Gordy (GS-911); Motown.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52