FEATURE BOILERS, PUMPS & VALVES
THE UNSUNG HERO OF BOILERHOUSE EFFICIENCY
with cold water. This is costly in terms of both water and energy because the cold feedwater must be heated. In contrast, condensate is already hot, which reduces the need for (and cost of) fresh water and treatment chemicals. It also requires much less energy than cold make-up water does to be ready for use. Flash steam can be harvested and re-
used. This is formed when high pressure condensate is exposed to a large pressure drop, often created during the blowdown process. A flash vessel is just one method that can be used to recover energy by separating flash steam from condensate. As condensate enters the flash vessel, flash steam is produced and can be piped from the top of the vessel to the feedtank through the deaerator. We can fit float traps to the outlet of
Boilerhouse managers and operators are under pressure to remain competitive and reduce costs, the search to combat energy consumption is top of their wish list. Chris Coleman, boilerhouse national specialist at Spirax Sarco, argues that truly efficient condensate recovery can boost productivity and improve regulation, at a much lower cost than we might imagine
I
t’s no longer enough to strike a good deal on energy supplies or achieve high
levels of productivity: now we are expected to do both, while complying with a complex web of regulation. Striking the right balance can make that crucial, tangible contribution to your company’s revenue flow, but, with ageing equipment and economic uncertainty coming into play, the potential to achieve precisely that is almost impossible. Until, we consider our use of condensate and the heat we may have otherwise wasted.
THE VALUE OF CONDENSATE To put it simply, condensate is the hot water that forms when steam passes from a vapour to a liquid state. It’s widely known that condensate is hot, but it’s only when we consider how this translates to heat energy that we realise how useful it is as a resource. The condensate generated by the steam heating system will normally have about 25 per cent of the energy that the steam had, and contains little to no dissolved solids. If the condensate is merely discharged
20 JUNE/JULY 2018 | IRISH MANUFACTURING
from the system and disposed of, that valuable energy resource is thrown away with it. That is an easily avoidable waste that few of us can afford. Draining condensate, rather than re-
using it, can trigger water and effluent management costs, which can be significant. Similarly, draining condensate can make it harder for us to comply with the regulatory standards around environmental effluent. In many countries, including the UK, condensate often has to be cooled before it can be drained which, again, will often come at an extra cost. Put bluntly, those who are disposing of their condensate are throwing money away. Recovering and re-using as much of it as possible can have huge financial advantages.
THE USES OF CONDENSATE We might now realise that condensate – and the heat energy it carries – is too valuable to be tipped down the drain, but how can it be put to better use? If condensate is not used as feedwater, the boiler must be topped up continually
the flash vessel where residual blowdown water will be drained. The water will still be hot at this point and is allowed to pass into the plated heat exchanger, where it gives up its heat to the circulating cold make-up water. In other words, we can recover the heat energy from the hot water coming from the flash vessel. The use of both a flash vessel and
plated heat exchanger pack will allow you to recover up to 80 per cent of the energy from the rejected Total Dissolved Solids (TDS) water, which can also result in fuel savings, a reduction in carbon dioxide emissions, and the elimination of unsightly plumes of steam.
Chris Coleman, boilerhouse national specialist at Spirax Sarco
THE RECOVERY PROCESS As you’re well aware by now, steam is usually generated for most industrial and process industries. Condensate recovery is one process that is genuinely capable of boosting boiler efficiency, saving energy, enhancing equipment lifespan and complying with legislation – all of which can, in turn, generate substantial savings to those who use steam systems. Rising energy costs are having a major
impact on all types of businesses across every industry. Saving energy from condensate is a simple, yet highly effective technique. It may not be the protagonist or the leading role in the steam system, but it is undeniably the unsung hero of the boilerhouse.
Read the full report online here
www.sxscom.uk/boilerhouseefficiency
/ IRISHMANUFACTURING
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36
