FEATURE COMPRESSED AIR
WHAT YOU NEED TO KNOW ABOUT COMPRESSED AIR DESICCANT DRYERS
expanded to atmospheric pressure and passed through the saturated desiccant, forcing the adsorbed moisture out. After desorption, the purge silencer valve is closed, and the vessel is re-pressurised. After regeneration, the functions of both towers are reversed.
HEATED BLOWER PURGE DESICCANT DRYERS Blower purge desiccant dryers use a combination of ambient air from an external blower, heat and a minimal supply of compressed air. In the drying process, wet compressed air flows upward through the desiccant, which adsorbs the moisture, again from bottom to top. In the regeneration stage, the blower
by Andy Lill, business development manager, Atlas Copco
WHY INDUSTRY NEEDS REALLY DRY AIR As any physics student can confirm, air in the atmosphere always contains moisture in the form of water vapour that’s not always welcome. In compressed air, it has the potential to cause problems. The result can be high maintenance costs, shortened service life and impaired air- user performance. Ultimately, untreated air can lead to premature failure of pneumatic equipment. It can also lead to a high rate of end- product rejection, increased leakage, disturbances in instrumentation and control systems, and shorter service life for pipework due to corrosion. Choosing a reliable desiccant dryer is
therefore essential to protect production systems and processes, maintain the quality of end products and minimise energy costs.
DRYER TECHNOLOGIES Regenerative-desiccant-type dryers are the primary choice for compressed air users within the pharmaceutical, chemical, and food and beverage manufacturing industries. They feature a porous desiccant that
adsorbs the moisture by collecting it in its myriad pores, allowing large quantities of water to be retained by a relatively small quantity of desiccant. The desiccant medium has a finite capacity for adsorbing moisture before it
10 JUNE 2020 | IRISH MANUFACTURING
must be dried out or regenerated. Normally, the desiccant is contained in two separate towers. Compressed air to be dried flows through one tower while the desiccant in the other is being regenerated. This is accomplished by reducing the pressure in the tower and passing previously dried purge air through the desiccant bed. The regeneration air may also be
heated, either within the dryer or externally, to reduce the amount of purge air required. Regeneration air may also be supplied by a blower and dryers of this type normally have a regeneration cycle, which can be based upon time, dew point or a combination of the two. The regeneration method depends on the type of desiccant dryer: heatless desiccant dryers or heated blower purge dryers.
HEATLESS DESICCANT DRYERS Heatless dryers use only compressed air as a purge. Because of their simple design, heatless desiccant dryers are often preferred for extreme environments. This sector includes operations in remote areas, hazardous sites with explosive gases and powders, and applications with a high inlet air temperature. In the drying process, wet compressed
air flows upward through the desiccant which adsorbs the moisture, from the bottom to top of the tower. During the regeneration cycle, dry air from the outlet of the drying tower is
takes ambient air and blows it over an external heater. The heated air is then sent through the saturated desiccant, forcing the adsorbed moisture out. This stage is followed by a cooling
purge: After the heating process is completed, the hot tower of desiccant is cooled by expanding dry compressed air from the outlet of the adsorbing vessel over the hot reactivated tower cooling the desiccant prior to use. As with the heatless process, the function of both towers is then switched automatically.
SUPERIOR ENERGY EFFICIENCY Pressure drop is an important factor in a dryer’s performance. A dryer’s energy consumption is determined by its internal pressure drop and the efficiency of its regeneration process. If a desiccant dryer experiences a high pressure drop, the compressor discharge pressure must be set higher, which increases energy and operating costs. The need for extra pressure requires more energy to produce, and in extreme circumstances may even require a larger output compressor to compensate for an output loss through the dryer, which in some cases can be as much as 20 per cent. Therefore, it is important to select
desiccant dryers that offer a very low pressure drop – below 0.2 bar for most models – as well as the most efficient regeneration process. In recent years, newer dryer technologies with state-of- the-art Elektronikon energy management controls, such as Dewpoint Dependent Switching, have been introduced to fulfil this requirement. The principle is simple. A dewpoint sensor will delay switching towers until the
/ IRISHMANUFACTURING
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36
