FEATURE PROCESS AUTOMATION DRIVEZ MEANZ SAVINGZ
After almost 20 years reliable service, engineers at the Kraft Heinz plant in Wigan decided to upgrade the drives on the pasta filling lines with the latest VLT AutomationDrive from Danfoss. The smooth, staggered installation has improved efficiency and saved energy
A
major upgrade project at the Kraft Heinz plant in Wigan has seen more
than 100 new Danfoss VLT AutomationDrive FC 302 variable speed drives installed to control conveyors in the pasta filling line production area. The installation of the new drives, which was carried out by Danfoss business partner PnP Motion Controls, was executed in multiple phases over a period of twelve months to avoid loss of production. The Kraft Heinz production facility in
Wigan is the largest food processing plant in Europe and it has 17 filling lines, a dedicated can-making factory, its own distribution centre, laboratories and a pilot plant. The site employs 1,600 personnel and has an annual production volume of 1.34 billion cans of food. At the heart of the plant is an extensive network of conveyors and fillers that must operate efficiently and dependably 24 hours a day, 7 days a week. When some of the lines were installed
almost two decades ago, control for the motors driving these conveyors was provided by Danfoss VLT 5000 series variable speed drives, which proved to be reliable throughout their many years of service. Recently however, the drives began to show a small but noticeable deterioration, as is characteristic of all electronic equipment of this age. This prompted the engineers at Kraft
Heinz to consider whether the drives should be replaced with more modern technology, that could offer better reliability. The idea of replacing the old drives was
made even more attractive by the knowledge that the new ones would also offer enhanced efficiency and saving energy. As a result, the decision was taken to go ahead with the drive replacement project, but the work was not without its challenges. An essential requirement, for example, was that the productivity of the plant must not be compromised. This meant that it would not be feasible
to replace all of the drives as a single operation. Instead Pete Brocklehurst, a Director of PnP Motion Controls, worked closely with Kraft Heinz to devise a schedule that would allow the new drives to be installed during plant shutdown periods for routine cleaning. A few drives
8 NOVEMBER 2018 | PROCESS & CONTROL
would be replaced during each scheduled shutdown, with the complete project spanning a year. All of the old drives were mounted in
control panels located in a control room, and it was decided that the new drives should be installed in the existing panels. Since the new drives were smaller, there was no space problem but the fixing arrangements were different. This challenge was easily overcome by using the conversion backplates supplied by Danfoss for just this purpose. Another challenge was ensuring that the
new drives were set up correctly, especially as the time available for installing and testing them was so limited. Once again, an effective solution was available. The settings from the old drives could easily be downloaded to a PC and, after processing with Danfoss conversion software, they were ready to be uploaded into the new drives. Not only was this arrangement quick and convenient, it also eliminated the possibility of error. Finally, arrangements had to be made
for the new drives to communicate properly with the plant’s existing
The availability of Danfoss products like adapter backplates, parameter conversion software and Profibus adaptors, means replacing VLT 5000 drives with their modern counterparts is straightforward
programmable controllers (PLCs). Since the connection between the drives and PLCs was implemented using Profibus, the most convenient solution proved to be the use of a Profibus converter card, which eliminated the need for program changes in the PLCs. The VLT AutomationDrive FC 302
Care was taken to minimise the number of drive sizes and variants used on the plant, to reduce spares requirements and simplify maintenance
products chosen as replacements feature a modular design to maximise versatility. The drives used at the Kraft Heinz plant mostly ranged in size from 0.75 kW to 2.2kW with a few larger types for special applications. Care was taken to minimise the number of drive sizes and variants used on the plant, to reduce spares requirements and simplify maintenance. While the new drives were being
installed, PnP Motion Controls took advantage of the opportunity to upgrade and reconfigure the Profibus network associated with the conveyor installation. “The project was very successful,” said
Pete Brocklehurst. “Thanks to the availability of Danfoss products like the adapter backplates, parameter conversion software and Profibus adaptors, replacing VLT 5000 drives with their modern counterparts is straightforward. And the benefits are substantial.” “While the old drives were best-in-class
when they were installed, the new VLT AutomationDrive FC 302 units are much easier to maintain, they run cooler - which means they’ll be even more reliable in service and have longer lives, and they’re more efficient, so they cut energy costs without compromising plant performance.” “Kraft Heinz is very happy with the
result of this upgrade to the plant, which will help to ensure that it continues to turn out over a mind-blowing 1.3 billion cans of beans, soup and pasta each year, for many years to come.”
Danfoss
drives.danfoss.co.uk
/ PROCESS&CONTROL
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44
