FEATURE MACHINE BUILDING, FRAMEWORKS & SAFETY


BUILDING A VIBRATION DETECTION SOLUTION


Thomas Brand, field applications engineer at Analog Devices, explains how to build a MEMS-based solution for vibration detection in condition monitoring


C


ondition monitoring is one of today’s core challenges in the use of mechanical facilities


and technical systems in which, for example, motors, generators and gears are used. To minimise the risk of production downtime, planned maintenance is becoming more and more important wherever machines are used. Among other things, the vibration patterns of the machines are analysed for this. The vibrations caused by the gearbox are


usually perceived in the frequency domain as a multiple of the shaft speed. Irregularities in the different frequencies point to wear, imbalance, or loose parts. MEMS- (microelectromechanical system) based accelerometers are often used for measuring frequency. Compared with piezoelectric sensors, they feature a higher resolution, excellent drift and sensitivity characteristics, and a better signal-to-noise ratio (SNR). They also enable detection of low frequency vibrations close to the dc range. In this article, a highly linear, low noise,


wideband vibration measurement solution based on the ADXL1002 MEMS accelerometer is shown. This solution can be used for bearing analysis or engine monitoring, and for all applications in which a large dynamic range of up to ±50g and a frequency response from dc to 11kHz are required. Figure 1 shows an example circuit. The analog


output signal from the ADXL1002 is fed via a 2-pole RC filter to the successive approximation register (SAR) analog-to-digital converter (ADC) AD4000, which converts the analog signal to a digital value for further signal processing. The ADXL1002 is a high frequency, single-axis


MEMS accelerometer that provides an output signal pass band extending beyond the resonant frequency range of the sensor. This is desired so that frequencies outside the 3dB bandwidth can also be observed. To accommodate this, the output amplifier of the ADXL1002 supports a small signal bandwidth of 70kHz. Capacitive loads of up to 100pF can also be directly driven with the output amplifier of the ADXL1002. For loads greater than 100pF, a series resistor ≥8kΩ should be used. The external filter at the output of the


ADXL1002 is required to eliminate aliasing noise from the output amplifier and other internal noise components of the ADXL1002 that arise, for example, through coupling of the internal 200 kHz clock signal. Therefore, the filter bandwidth should be implemented accordingly.


14 APRIL 2021 | DESIGN SOLUTIONS


Figure 1. Example circuit for the ADXL1002


With the dimensioning shown in Figure 1 (R1 = 16kΩ, C1 = 300pF, R2 = 32kΩ, and C2 = 300pF), attenuation of about 84dB is achieved at 200kHz. Also, the selected ADC sampling rate should be higher than the amplifier bandwidth (for example, 32kHz). For the ADC, the ADXL1002 supply voltage


should be selected for its reference because the output amplifier has a ratiometric relationship with the supply voltage. In this case, the voltage supply tolerance and the voltage temperature coefficient (which are usually connected to external regulators) run between the accelerometer and the ADC so that the implicit error associated with the supply and reference voltages is cancelled out.


FREQUENCY RESPONSE The frequency response of the accelerometer is the most important characteristic of the system and is shown in Figure 2. The gain increases at frequencies above about 2kHz to


3kHz. For the resonant frequency (11kHz), a peak value for the gain of about 12dB (factor of 4) in the output voltage is yielded. To display measuring range overshoots


(overrange), the ADXL1002 has a corresponding output (OR pin). The integrated monitor emits a warning when a significant overrange event occurs.


MECHANICAL CONSIDERATIONS REGARDING MOUNTING Special attention should be paid to correctly placing the accelerometer. It should be mounted close to a rigid mounting point on the board to avoid any vibrations on the circuit board itself and thus measurement errors due to undamped circuit board vibrations. The placement ensures that every circuit board vibration on the accelerometer lies above the mechanical sensor resonant frequency and hence is practically invisible to the accelerometer. Multiple mounting points close to the sensor and a thicker board also contribute to lowering the impact of system resonance on the sensor performance.


TO CONCLUDE With the circuit shown in Figure 1, a MEMS-based solution for detecting vibrations from the dc range to 11kHz, as is often required in condition monitoring of rotating machines, can be built relatively easily.


Analog Devices www.analog.com


Figure 2. Frequency response of the ADXL1002 / DESIGNSOLUTIONS


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44