FEBRUARY 2024 Ӏ NEWS
NEW LUFFER FROM POTAIN’S ZHANGJIAGANG FACTORY
Wisconsin, USA-headquartered crane manufacturer Manitowoc has launched the all-new Potain MCR 305 luffing jib tower crane, which was jointly developed by French and Chinese engineers. The crane is being manufactured at the Manitowoc factory in Zhangjiagang, China, and will be sold across Asia, Australia and New Zealand, Africa, the Middle East, and Latin America. Customer feedback harnessed through
the company’s Voice of the Customer process was used to optimise the new design, offering several improvements over earlier models. A key improvement, says Manitowoc, is that the new Potain MCR 305 can reach a height of 190 m with almost half the anchorage points required by similar models. Requiring fewer anchorage points, the company explains, means more efficient assembly and less expense for contractors – saving precious time on the tight schedules high-rise projects demand. For example, with the existing MCR 295 A configured with a 60 m jib, 11 anchor points are required to reach a height of 192.6 m; with the new MCR 305, with the same jib, just six anchor points are needed to reach 194.3 m. The crane also has a smaller out- of-service radius optimising space on
jobsites for better productivity and profitability. With a 60 m jib the out-of- service radius of the MCR 305 is just 12.5 m compared with 22 m for the MCR 295 A in the same configuration. According to Manitowoc lowering the
out-of-service radius allows contractors to place more cranes on constrained jobsites making more lifting options available and delivering better space optimisation. It says this could mean projects considering a high-rise build with just one crane may now be able to accommodate two, thus delivering productivity advantages. Two versions of the crane are available:
one with a maximum capacity of 20 t and a 3.1 t tip load with a 60 m jib. The other with a maximum capacity of 25 t and a 3 t tip load with the same 60 m jib. There are multiple winch options, depending on customer preference, including HPL (High-Performance Lifting) options with up to 1,200 m of wire rope available. “The new crane’s increased load charts
make the MCR 305 more attractive for high-rise construction, as it can handle heavier loads,” said Leong Kwong-Joon, regional product manager for Potain tower cranes at Manitowoc. “We had extensive conversations with customers and the insights we gained have helped us develop an impressive new luffing jib crane. Strength gains are realised along the entire length of the jib. There are also great savings for customers in climbing higher faster, and better productivity with a substantially reduced out-of-service radius. We’re excited to launch this new model to market.” Basic design, wind performance, and wind tunnel tests for the crane were carried out in France, while the Chinese team completed the structural design and test verifications. Each jib position and lifting point on the crane was subject to an extensive design and analysis process lasting several months.
12 CRANES TODAY
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53
