MATERIALS HANDLING The double
flush inlet configuration ensures a robust pressure differential and maintains consistent sealing performance
3. Single flush inlet with reduced outlet drain
Simulations were conducted using a SealRyt PackRyt Bearing with an Integrated Lantern Ring (BLR) and a large slurry pump. The PackRyt Bearing’s tight tolerances and advanced design allow for precise control over fluid dynamics within the stuffing box, resulting in satisfactory sealing. For plants relying on packing only to seal their shafts, the flow rates can vary drastically from installation to adjustment. Additionally, achieving the crucial 15 psi differential needed to prevent process material from entering the stuffing box is much more challenging with packing-only systems. Other bushing products that lack the tight tolerances of the PackRyt Bearing are likely to experience sealing results similar to packing-only systems.
KEY FINDINGS 1. Config A: Single flush inlet
This setup introduces flush fluid at 300 psi, but the pressure drops by 8 psi before reaching the lantern ring. With only a 7 psi differential, the seal fails to maintain consistent performance, and thermal expansion further decreases the flow rate over time.
2. Config B: Double flush inlet In this optimal configuration, two
inlets supply flush fluid at 300 psi. The pressure drop to the lantern ring is minimal (2 psi), achieving a 13 psi differential—well within the recommended range. The initial flow rate of 8.5 GPM is sufficient, and the system remains stable even with thermal expansion. For shafts over 7” in diameter, this configuration is highly recommended wherever possible to ensure reliable sealing.
3. Config C: Single flush inlet with reduced outlet drain Here, the inlet flush also starts at 300 psi but suffers a 10 psi drop before the lantern ring. The reduced outlet drain exacerbates pressure loss, allowing process media to breach the seal. The flow rate dwindles to 1.3 GPM, leading to seal failure and potential heat damage.
WHY DOUBLE FLUSH INLET WORKS BEST The double flush inlet configuration ensures a robust pressure differential and maintains consistent sealing performance, even in high-pressure, high-heat environments. Its ability to distribute flush fluid effectively prevents the media from compromising the seal and reduces wear and tear on equipment. Longer nose lengths in the bearing design further enhance the fluid restrictor’s effectiveness, a feature critical in mining operations where stuffing box construction often limits single inlet efficacy.
CONSIDERATIONS FOR EFFECTIVE SEALING While choosing the optimal flush configuration is essential, other factors that significantly influence sealing performance are as follows:
Startup procedure: Proper startup procedures ensure that seals are not exposed to unnecessary stress during initial operation. Gradually bringing systems up to operating pressure and temperature minimises the risk of early failure.
Shaft condition and alignment: A well-maintained and correctly aligned shaft prevents uneven wear and ensures consistent contact with the sealing surfaces. Misalignment or damage to the shaft can lead to premature seal degradation.
Flush supply quality and pressure: The quality of the flush fluid—free from contaminants and debris—is critical. Consistent and adequate flush pressure ensures the barrier fluid maintains its protective role and prevents process media from breaching the seal.
THE REALITIES OF MINING OPERATIONS In mining operations, conditions are rarely ideal. Compromises are often necessary, and the best-run operations excel by problem solving and making the most of available resources. This includes seeking expert advice when needed and remaining skeptical of the status quo. Leveraging sealing experts can provide tailored solutions that address unique challenges and improve overall performance.
BETTER SEALING PRACTICES Better sealing practices can transform mine operations. Adopting the double flush inlet configuration can significantly reduce maintenance costs, improve operational reliability, and enhance safety. Mining operations using this configuration benefit from:
- Reduced risk of seal failure - Improved longevity of rotating equipment
- Lower downtime and associated costs
CONCLUSION CFD simulations confirm that the Double Flush Inlet configuration is the superior choice for shaft sealing in mining applications. By embracing this innovative approach and incorporating considerations like startup procedures, shaft condition, and flush supply, quality, mining companies can safeguard their operations against leaks, downtime, and equipment damage—ensuring smoother, more efficient processes. For shafts over 7” in diameter, a Double Flush Inlet configuration is strongly recommended.
For more information visit:
www.sealryt.com
www.engineerlive.com 45
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
