perience with radiography ratings and casting performance. No correlation between radiography and ultrasonic ASTM ratings presently exists. Therefore, no one is sure how ASTM UT ratings correlate with casting performance or radiography.
The goal of the project is to determine the repeatability of UT inspection on steel castings. Additionally, the project will correlate UT ratings to radiographic ratings. This will assist foundries in understanding UT and enable them to appropri- ately use the technology.
Status Update: Round-robin testing for UT (including phased array) and x-ray is now being conducted. Anyone interested in how they might participate in this project should contact Prof. Bob Tuttle, Saginaw Valley State University, at
rtuttle@svsu.edu.
Aging and Machinability Interactions in Ductile Iron (08-09#02)
Coordinator: Missouri University of Science and Technology (MS&T) and AFS Cast Iron Division (5)
The proposed overall program will complete the understanding of how age strengthening affects machinability so that found- ries may be able to utilize the strength improvement with age strengthening to cast equivalent grades at higher carbon equiv- elent (CE), lower alloy or lower pearlite content without the re- quirement to hold castings before machining. The objective of the proposed work is to explain the mechanism by which age strengthening changes the machinability of graphitic cast irons to investigate ductile irons.
Little is known about age strengthening effects on machin- ability of ductile iron. It has been shown that age hardening of the free ferrite microstructure component of ductile iron exceeds the tensile strength increase of the bulk material. Work with ductile iron would not only provide information specific to ductile iron but could shed light on the general mechanism for age-strengthening effects on machinability in graphitic cast irons due to the larger amount of free ferrite that can be obtained in as cast alloys such as 65-45-12.
Status Update: The project work is ongoing and progress was reported in papers given at CastExpo’10 & Congress. Those interested in the work of this project or committee should con- tact Prof. Von Richards, Missouri University of Science and Technology, at
vonlr@mst.edu.
Optimizing Mechanical Properties of Cast Aluminum Alloys by Molten Metal Treatment (Phase I A356)—CWRU (Agreement 08-09#04)
Coordinator: Case Western Reserve University and AFS Alu- minum Division (2)
Mechanical properties of cast aluminum products can exhibit wide variation even when the same alloy is used. Best practices to achieve maxi-mum properties encompass: high molten metal quality (clean metal, degassing), metal treatments (modification,
82
grain refining), good gating practices, filtration, directional so- lidification, fast cooling rates and adequate risering. The indus- try would benefit from a well-defined set of “potential” (i.e. maximized) properties that can be achieved for any given alloy when best practices are applied.
This project proposes to establish a data base with “potential” properties of cast aluminum alloys, in other words, if Best Practices in melting the aluminum and treating it are carefully followed, a high cooling rate is applied and shrinkage porosity is eliminated, what would the properties be?
Status Update: The first progress reports were given at AFS Aluminum Division meetings. Those interested in the work of this committee should contact Steering Committee Chair David Neff,
theneffers@sbcglobal.net, or David Schwam, Case West- ern Reserve University, at
dxx11@cwru.edu.
Ductile & CG Iron Casting Skin - Evaluation, Effect on Fatigue Strength & Elimination Phase II (09-10#01)
Coordinator: Ohio State University and AFS Cast Iron Divi- sion (5)
The elimination of the flake skin is one of the key elements of unlocking the full design potential of Compacted Graphite Iron (CGI). Capitalizing on the results of a previously AFS sponsored effort 04-05#02, “Study of the Effect of the Casting Skin on the Tensile Properties of Light Weight Ductile Iron Castings”, the Department of Materials Science and Engineering at The Ohio State University (OSU) proposes to conduct research with the goal of understanding the mechanism of formation of casting skin in CGI, evaluating its effect on selected mechanical proper- ties, and developing the methodology for its complete elimina- tion. The results of this research will be of immediate applicabil- ity to the industry without major capital investment.
The research strategy is designed to develop the knowledge re- quired to improve and ultimately eliminate skin quality of CGI castings and to generate data on its impact on the static mechani- cal and fatigue properties of CGI, as well as on the efficiency of shot blasting in improving these properties. Additionally, the study may help in the definition of the minimum thickness of the layer that must be removed by machining to avoid negative skin quality effects. The research will capitalize on the experience in the characterization of casting skin accumulated in the Virtual Solidification and Casting Laboratory (VisionCast) at OSU.
The success of this investigation will rely on the completion of extensive experimental work that will provide critical data required in the understanding of casting skin formation and elimination. The developed correlations between process variables, casting skin quality and mechanical properties will provide the impetus to fur- ther expand the applications of CGI. During Phase I, the mecha- nism for skin formation and test specimens design was validated. During Phase II fatigue specimens will be cast and influence of skin formation of fatigue will be determined. Also, potential ac- tions to reduce or eliminate skin formation will be investigated.
International Journal of Metalcasting/Spring 10
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89