Speco Technologies Commercial Audio Guide What Is a 70 Volt Sound System & What Is It Used For?
A 70 Volt Sound System is comprised of amplifiers, speakers with transformers, microphones, volume controls, a telephone system interface and an assortment of wires used as connections. It is generally used for commercial sound applications where there is a need for electronically amplifying and distributing sound for the functions of paging, playing music and/or pre-recorded messages to a commercial environment.
What Are The Components That Make Up a 70 Volt Sound System?
• Centralized Amplifier: The central unit of a 70 Volt System is the amplifier that boosts the sound signal to be distributed to pre-established speakers or paging horn loudspeakers.
• Speakers: There are several different types of speakers including in-ceiling, in-wall, baffle and flush-mount cone speakers or horn loudspeakers.
For 70 Volt Systems in commercial applications, the speaker must have a transformer mounted on it to be used.
• Transformers: Transformers that are used on 70 Volt System speakers are step-down transformers that convert the high-voltage/low-current coming from the amplifier to the low-voltage/high-current signal going to the speaker.
A transformer most often has multiple wattage taps that allow each speaker to be individually set as to how much wattage will enter the speaker and how loud each speaker will be. Transformers can be sold individually to be mounted on a speaker or premounted on a speaker.
• Phone System Interface Device: These systems are used to connect a phone system to the speaker system via an amplifier for paging purposes.
• Microphones: Located in the front end of the system, they will receive the delivered sound. Microphones are typically low impedance devices that require a shielded cable so as to not to interfere with the amplifier or speaker wires.
• Wires: Generally, speaker wire is determined by the length of the run and wattage utilized: For wire runs less than 50 ft. and 50 Watts of power or less use 16 gauge wire. For wire runs more than 50 ft. or over 50 Watts of power use 14 gauge wire.
• Volume Controls/Attenuators: Allow adjustment of volume to speakers.
What Are The Benefits of Using a 70 Volt Sound System? • A 70 Volt System uses a basis of high voltage to result in a lower current when distributing power to a sound system. Power equals Voltage times current, thus a higher voltage will result in a lower current needed to arrive at a desired power load.
• Generally speaking, 70 Volt Systems are much more cost efficient than an 8 Ohm speaker system when dealing with volume installation of speakers.
• 70 Volt Systems are easier to design than 8 Ohm speaker systems. The impedance does not have to be matched throughout the 70 Volt system as it would on an 8 Ohm based system.
• An easy calculation is all that is needed in determining the amount of wattage needed by your
amplifier. Take the total wattage requirement of the 70 Volt speakers, or “load”, include a 20% safety buffer to the upside and you will obtain the minimum RMS wattage.
• 70 Volt Systems allow the volume of each individual speaker in a specific area to be set using wattage taps. The higher the wattage taps are set on individual speakers, the more power the speaker consumes, the louder the speaker will be.
• The speaker transformer serves as a safeguard to make sure individual speakers are not damaged by excessive wattage.
Speaker 1 Floor Speaker 2
Designing a 70 Volt System: Which Type of 70V Speaker Should I Use? In-Ceiling Speakers – Best utilized in 8, 10 & 12 ft. drop ceilings in professional environments with low noise levels. Great for background music and/or paging. Ceiling support brackets should be used with in-ceiling speakers.
Wall Baffle or Wall Mount Speakers – Best utilized when the ceiling’s height is prohibitive to speaker placement and/or speakers can not be mounted on the ceiling at all.
PA Horns – Horns are usually utilized in loud environments when distinct, and powerful paging messages are needed or when large areas must be covered. In addition, most PA Horns are weatherproof and are used for outdoor applications such as loading docks and sports fields.
How Many Speakers Should I Use? Determining Proper Use Quantity For In-Ceiling Speakers:
The industry standard for calculating the proper amount of in-ceiling speakers for a specific area is to should have twice the space from the floor to the ceiling between the placement of each speaker on the ceiling, as shown in Diagram 1:
Diagram 1: Speaker Spacing on Ceilings Ceiling Speakers Should be Spaced Apart at Twice the Space of the Ceiling Height ◀ Ceiling - 16 ft. ▶
For example, if your installation involves an 8 foot ceiling, then the speakers should be placed 16 feet apart on a square footage basis which equals 256 ft. of ceiling area covered.
The following square area coverage chart shows specific ceiling heights: Speaker Square Footage Coverage for Ceiling Heights
8 foot ceiling 10 foot ceiling 12 foot ceiling
Height of Ceiling 8 ft.
10 ft. 12 ft.
Spacing of Speakers (ceiling height x2)
16 ft. 20 ft. 24 ft.
Square feet coverage per Speaker
16 x 16 = 256 ft. 20 x 20 = 400 ft. 24 x 24 = 576 ft.
As you will notice, lowering the ceiling height results in the less square footage coverage per speaker, or the more speakers you will need. This is due to there is less downward space for sound dispersion before it reaches the listener.
◀
▶
8 ft.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68