FEATURE WORKPLACE SAFETY F
or manufacturing businesses, sustainability means developing both long-term and
short-term production strategies that balance profits with environmental protection and worker safety. Businesses must decrease emissions, improve energy efficiency, protect natural resources, reduce waste and protect the health and well-being of their workers. The sustainability objective is to meet today’s short- term goal of commercial success without overlooking the long-term impact operations might have on workers and the planet.
MEETING SUSTAINABILITY STANDARDS In many instances, governments set standards, rules and regulations to help manufacturers reach their sustainability goal of protecting both the planet and their workers. An example is the Montreal Protocol agreement, an international, collaborative treaty devised to protect the ozone layer. The purpose of treaty, adopted in 1989, is to phase out the production and use of ODS (Ozone Depleting Substances). It identifies a list of ODS that threaten human health by lessening the earth’s protective stratospheric ozone layer. Some ODS are strictly controlled for their use. Others are targeted for phasedown and others were completely phased out. The Montreal Protocol made a lasting impact
in many industries, but particularly within the metalworking industries where solvents are used for parts cleaning. For example, in the 1990s many metal working shops used chlorofluorocarbon (CFC) and hydrofluorocarbon (HCFC)-based solvents inside vapour degreasing machines to clean parts. These included CFC-113, 1,1,1-trichloroethane, HCFC-141b and HCFC-225. They effectively removed grease, oils and other industrial soils from parts. However, they also had very high ODP (Ozone Depleting Potential) ratings. By the mid-1990s their use was highly regulated and ultimately, they were banned for metal cleaning altogether.
FINDING ALTERNATE SOLUTIONS At that point, many manufacturers switched to aqueous, or water-based cleaning methods. However, aqueous cleaning scores low for environmental sustainability. It uses water, a finite and, in many areas, non-renewable resource, to clean. It also requires large amounts of energy, either electricity or natural gas, to remove impurities, balance pH and then heat the water for cleaning. Plus, it produces wastewater that must be treated to remove soils and detergents before it can be reintroduced to the environment. In other instances, some industries moved to
high-solvency chlorinated and brominated solvents such as TCE (Trichlorethylene) and nPB (n-Propyl Bromide). But those alternatives are now facing scrutiny due to their air quality concerns. They are also suspected of being toxic to plants, fish and animals. These concerns resulted in the establishment of
REACH (Registration, Evaluation, Authorisation and Restriction of Chemicals) legislation. REACH is a European Union regulation, established in 2006. It controls the production, import, and use of
18 SUMMER 2020 | INDUSTRIAL COMPLIANCE
How sustainability improves worker safety
As manufacturers become increasingly aware of the importance of sustainable practices, MicroCare has a range of highly-advanced cleaning products which have been developed to not only clean effectively but in a work safe, economically and environmentally sound way. In this article, Venesia Hurtubise, technical chemist at MicroCare discusses the importance of sustainable cleaning
chemical substances within the European Union. REACH regulation Article 59(10) discourages both TCE and nPB use. Currently, TCE has a carcinogen classification. It has not been available for vapour degreaser cleaning in Europe, without special authorisation and stringent controls on factory emissions, since 2016. And under EU REACH regulations, nPB will soon need special permission for use in Europe after July 2020.
AIR QUALITY IMPACTS EVERYONE As a result, safer solvents and cleaning fluid blends are now available. Many of these modern metal cleaning fluids are HFO (hydrofluoroolefin)- based which gives them a combination of a good environmental sustainability along with excellent worker safety profiles. For example, the modern cleaners have a low
GWP (Global Warming Potential). The GWP of a cleaning fluid is a measurement of the atmospheric lifetime of the fluid or its gaseous vapours. The longer a trapped gas absorbs infrared radiation in the atmosphere, the more it may contribute to global warming and climate change. The new cleaning fluids typically have a low GWP of three or less. By comparison, the old HCFC solvents had average GWP ratings in the thousands. Plus, the ODP of modern cleaning fluids is zero, meeting all EU air quality emissions regulations.
SUSTAINABLE AND WORKER SAFE In addition to preserving air quality by producing fewer emissions, the modern sustainable cleaners offer worker safety benefits. First, unlike legacy solvents, modern cleaning fluids
are nonflammable. This is an important benefit to plant environmental health and safety managers since it helps protect their workers from burn injuries if an accident, such as a sudden arc flash, occurs. Second, modern sustainable cleaning fluids have
very high marks for worker exposure limits. The PEL (Permissible Exposure Limit) or designated time limit that workers should be exposed to a chemical is much higher for sustainable cleaning fluids. Permissible exposure levels for sustainable fluids are about 200-250 ppm. Compared with TCE which has a 100-ppm PEL or nPB that is rated at just 0.1 ppm, the sustainable cleaning fluids are significantly better for the safety of exposed workers.
THE NEXT STEPS FOR SUSTAINABILITY Leading manufacturing companies are setting ambitious goals to produce their products more sustainably. This means they are developing ways to meet company goals of customer satisfaction and economic success in the short- term. But also respecting environmental limits and ensuring the long-term health and safety of the planet and their workers. For companies looking to change to sustainable
cleaning fluids, it is essential to work with a partner that has sustainable cleaning fluid and vapour degreasing expertise. Based on specific parts make-up and the contamination encountered, they can recommend the sustainable fluids and cleaning methods that will work best.
MicroCare
www.microcare.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32
