PC-MAY24-PG34.1_Layout 1 15/05/2024 12:11 Page 34
PUMPS, VALVES & ACTUATORS
THERMODYNAMIC MEASUREMENTS MINIMISE PUMP OPERATING COSTS
Dr Tom Clifford, from Riventa, looks at how to provide clear, compelling answers to that top- down mandate on reducing the energy costs associated with pump operation
ust when you thought pressures could not get any greater, in comes another top-down mandate to reduce energy costs even further, because another massive bill for electricity has landed.
J
You’ve already looked at the pumps, which with their big motors, is an obvious place to start to try and make savings. Typically accounting for around 80% of electrical energy in process operations, knowing exactly how they are performing is of course, a key metric.
But if you’re restricted to sub-metering alone, then according to one optimisation expert, this is akin to putting fuel in your car, but never knowing how many miles have been driven.
“Electrical sub-metering will give you some basics, and tick some KPI boxes, but it’s not going to give you anywhere near the full picture,” says Dr Tom Clifford, Co-founder and CTO at Riventa. “Computing the efficiency of a pump through measurements of differential pressure and temperature will give you a figure to work with,” he said, “followed by the input power to the pump, which is usually obtained by measuring gross electrical power, and an assumption of motor efficiency.”
Clifford states though that whilst this conventional, pressure-flow method of measuring pump efficiency is resilient for all head ranges from zero upwards, it is really
only suitable and accurate for a test loop. For actual site use, this, with the absence of straight pipe in the individual pump main, immediately presents problems. Installing a flow meter on each and every pump is also too costly, and space constraints limit the accuracy of the application.
Another scenario that can prompt far more detailed performance evaluation will inevitably be related to ever increasing electricity costs.
Above: FREEFLOW technology can identify energy savings from real-time monitoring
Left: Riventa can highlight potential reductions in life- cycle costs Below: Accurate and high quality data can determine the health and efficiency of pumps
savings of £20,000 were identified for the cooling system.
Clifford added: “It’s easy to describe such a frustration as ‘an opportunity’. Again, conventional methods of measurement have serious limitations, so a deeper dive into what’s really going on can sort issues once and for all, and create substantial savings, which is where thermodynamics comes to the fore.”
In essence, if you measure any two thermodynamic state variables (TSV), which include temperature and pressure, you can calculate any other TSV. For example, pump efficiency can be measured through a half- inch BSP (British Standard Pipe) tapping on each side of the pump, which is perfect for in-situ, on-site pump performance monitoring, and does not require the straight pipe lengths that conventional testing relies on.
“Capital cost and installation costs of thermodynamic testing are lower and irrespective of pump size,” continued Clifford. “Very importantly too, you’re going to get far superior accuracy at higher heads, measuring each pump, individually.” Clifford pointed to a recently example at a food processing facility, where annual
34 MAY 2024 | PROCESS & CONTROL
He added: “To evaluate the horizontal end- suction pumps, which are driven by a motor with an inverter drive (to allow control of the flow rate), we used thermodynamic measurement techniques, including suction and discharge pressures either side of the pump, differential temperature, and motor input power. This allowed us to calculate differential head across the pump, hydraulic efficiency, and volumetric flow. “Part of our work involved ‘throttling’ the pumps so that we could carefully observe the maximum possible flow through each pump under test, without altering the overall flow to the plant. Relative to the manufacturer’s typical performance, data showed that the shape of the pump curves indicated severe internal recirculation due to high wear ring clearances.”
Clifford concluded: “The advances that have been made in semiconductor electronics and hydraulic analysis methods can’t be ignored if you want to provide clear, compelling answers to that top-down mandate on reducing energy costs. Real- time pump monitoring with integrated decision support software is now readily available. It acts like a sat-nav, providing real-time instructions to help meet the minimum possible operating cost, even when system factors are changing.”
Riventa
www.riventa.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56
