CRYO-SEM & CRYO-FIB/SEM PREPARATION EDITION III zzzCryo Transfer Systems (continued)


SPECIFICATIONS for PP3004, PP3005, PP3006 PP3004


Temperature Cooling Runtime LN2 Dewar Capacity


Cool-Down Time to -190°C Rapid Freezing (slushy LN2) Dewar Trolley Footprint Airlock Weight


Pumping Requirements Nitrogen Gas


Ambient N/A N/A N/A N/A N/A


2.5 kg Rotary pump or dry pump For venting and valve operation


Power Requirements (excluding pump) 300 W Maximum Specimen Size


PP3005


RT to -190°C Up to 24 hours 21 liters


Typically <15 minutes Optional (24429) 50 x 50 cm 2.5 kg


Rotary pump or dry pump Venting and cooling 300 W


PP3006


RT to -190°C Up to 24 hours 21 liters


Typically <15 minutes Optional (24429) 50 x 50 cm 2.5 kg


Rotary pump or dry pump Venting and cooling 300 W


Flat specimens up to 23 x 26 mm. For taller specimens the maximum height will reduce from a mid-point of 9mm. Please contact us for more details.


ORDERING INFORMATION For a full quotation, including on-site installation and customer training, please contact us. Cat. No.


Description PP3004


QuickLok Ambient Temperature Transfer System Includes:


Airlock assembly. Pump and vent and transfer controls, valve and fittings to the pumping system (see: Pumping below). Custom designed interface flange to the microscope vacuum chamber


Microscope dovetail stage to accept specimen shuttle. LED chamber light (interlocked)


Specimen transfer device for vacuum or inert gas transfer Specimen holders. Specimen shuttle with holding clips, specimen shuttle blank, specimen shuttle (to hold a 10mm dia. specimen stub), blank 10 mm stubs – packet of 10


PP3005


SEMCool Non-Airlock Low Temperature System Includes:


Nitrogen gas cooled cold stage with heater and sensor and cold trap with temperature sensor. Temperature controllable with a range down to -190°C, 21 L liquid nitrogen dewar with trolley, heat exchanger and LED chamber light. Pump fittings (see: Pumping below).


Temperature and nitrogen gas flow controller mounted on the dewar trolley.


Specimen holders. 3 specimen shuttles (to hold 10 mm Ø cryo stubs), blank specimen shuttle, specimen shuttle with holding clips, blank 10 mm Ø stubs (packet of 10), 5 multi-purpose specimen stubs. Note: other holders available Specimen mounting compounds (colloidal graphite and Tissue-Tek®


) PP3006


CoolLok Cryo Transfer System Includes:


Airlock assembly. Pump and vent and transfer controls, gate valve and fittings to the pumping system (see: Pumping below). Custom designed interface flange to the microscope vacuum chamber. Cooling system. Nitrogen gas cooled cold stage with heater and sensor and cold trap with temperature sensor. Temperature controllable with a range down to -190°C, 21 L liquid nitrogen dewar with trolley, heat exchanger and LED chamber light. Specimen transfer device


Specimen holders. 3 specimen shuttles (to hold 10 mm Ø cryo stubs), blank specimen shuttle, specimen shuttle with holding clips,blank 10 mm Ø stubs (packet of 10), 5 multi-purpose specimen stubs. Note: other holders available Specimen mounting compounds (colloidal graphite and Tissue-Tek®


), interlock cable and pump fittings PP7450 13296 each Qty. Cat. No. Pumping


The PP3004 QuickLok and PP3006 CoolLok require either a rotary pump or high vacuum turbomolecular pumping station (recommended). The PP3005 requires a rotary pump for evacuating the vacuum isolated gas lines. 13034


Pfeiffer Duo 6 — 5 m3 with oil mist filter


24426


Options and Accessories 24429


/hr rotary vacuum pump


Pfeiffer HiCube 80 turbomolecular and diaphragm pumping system


Rapid cooling station (for PP3006 only)


Consists of a floor-mounted trolley, liquid nitrogen freezing chamber mounted into the work surface which interfaces to the cryo transfer device, connections to vacuum pump (order separately)


Pressurized (60 L) LN2 dewar.


Boil-off nitrogen gas is used for cooling the stage and cold trap (PP3005 and PP3006 only)


Sircal in-line gas dryer. Helps to reduce water content of nitrogen gas supply


Specimen Holders 10245


each


10246 10247 E7433


E7449-5 E7401 E7402 E7403 E7405 E7406 E7407


32816510


Top-loading specimen shuttle for planchettes Top-loading specimen shuttle, to take a 10mm stub Top-loading specimen shuttle for rivets (vice style)


Rivet holder specimen stub, screw-down style (for use with 10246)


each each


each each each


Universal specimen stub with surface holes and slots (5 pack) each Specimen stub shuttle (spare) Aluminum (Al) stubs (10 pack) Copper (Cu) stubs (10 pack)


Screw down stub for thin, hard specimens Copper (Cu) stubs with 3 x 3mm slots (5 pack) Copper (Cu) stubs with 1 x 3mm slot (5 pack) Brass rivets for fracturing liquids (100 pack)


Sputter Targets and Carbon Fiber E7400-314A Gold (Au) target 0.008" thick


each


E7400-314B Gold/palladium (Au/Pd) (80:20) target 0.2mm thick E7400-314C Platinum (Pt) target 0.008" thick E7400-314IR Iridium (Ir) target 0.008" thick E7400-314CR Chromium (Cr) target 0.3mm thick Carbon fiber cord — high purity — 1m Carbon fiber cord — high purity — 5m


91047-1 91047-5


each each each each each each


each each each each each each each


each each


each


each each


Description Qty.


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16