APPOINTMENTS & NEWS 7


NEWS FEATURE


Getting it right when tanking a wetroom


Marmox’s silver jubilee a roaring success


At the big Cat Sanctuary in Kent, around 50 of Marmox’s staff and family gathered to relax and celebrate the company’s 25 years in business. After visiting Lions, Tigers, Pumas, Jaguars, Cheetahs and Leopards, they enjoyed a buffet lunch before founder Harry Parsons cut a cake suitably decorated with the company logo and gave a short speech on, as he put it, ‘how it all started.’ This was followed by Sarah Viney, Harry’s daughter and managing director and her brother Jonathan Parsons who is business development director, together with long time member of the Marmox team, fi nance director, Richard Kent- Smith presenting certifi cates to many long serving employees and as an extra thank you, under each guest’s glass on the dining table was a lottery ticket – so three lucky winners’ prize was to feed the Tigers. While Marmox remains a family business, staff retention across the company’s various departments is excellent, with the stability this offers boding well for the future. Here, Sarah sees the industry as shifting towards off-site fabrication, in the knowledge Marmox is well place to respond.


01634 835290 www.marmox.co.uk Nick Bratt, national technical sales manager for tile adhesive


manufacturer Palace Chemicals, outlines the importance of the correct use of materials and good practice, as defi ned in the relevant British Standards, when it comes to tanking a bathroom or wetroom.


W


ith the continuing growth in popularity of wetrooms, we are seeing a corresponding increase in incidents where the installation has not been satisfactory, and often this is caused by water or moisture getting into the substrate behind the tiles. These issues are very diffi cult to solve post-installation but can be easily prevented at the design stage by following the guidance contained within the British Standard relating to tiling.


Supplier SPOTLIGHT


BS 5385-1 2018 states that for all new or refurbished properties, a proprietary tanking system should be used. BS 5385-3, concerning fl oor tiling, was updated in 2024. One of the key amendments is for direct tiling on to plywood and other wood-based sheets or boards, an intermediate layer, such as an uncoupling membrane, reinforced tanking system or tile backer board should be used, providing the plywood is rigid and stable enough to carry the expected in service load. The new standard also states that timber is not recommended as a suitable substrate for fl oor tiling in wet, frequently damp, or high humidity areas. For wetroom fl oors, they should be laid to falls with gradients of between 180° and 135° to ensure that the water fl ows towards the drain, taking note that a gradient any greater than 135° is unsuitable and possibly dangerous. This requirement impacts on the design of wetrooms in particular since they are subject to repeated and persistent wetting, and a suitable proprietary tanking system should be used prior to tiling. This should be laid continuously around upstands and points where services pass through the fl oor, to create a seamless seal, so that there is no risk of water leaking through to the substrate. If using other intermediate substrates, such as moisture resistant


boards, the manufacturer’s technical data and/or the manufacturer itself should always be consulted, as these would usually state that a tanking system should be used. The recent updated release from NHBC has sparked some controversy due to the wording around fl ow rates of a shower and moisture resistant boards, as these contravene the British Standards guidance for tanking.


For walls which surround a bath where a shower is not fi tted then the substrate should be suitable for the application and moisture resistant. It is important to recognise that water resistant adhesives and grouts are designed to allow water to pass through them without them breaking down, hence ‘water resistant’, but are not a substitute for a waterproof tanking system, as clearly stated in BS 5385 Part 4. If in doubt, tank it out! That way, any and every project that has wet, frequently damp, or high humidity areas will always have the added insurance policy that there will not be any leaks!


WWW.LINKEDIN.COM/SHOWCASE/SUPPLIER-SPOTLIGHT


Supplied by Nick Bratt, national technical sales manager for Palace Chemicals


WWW.BUILDINGCONSTRUCTIONDESIGN.CO.UK


Your new Source of Manufacturing insights!


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32