TEXTURED SILVER GREY


WE HAVE A SELECTION OF COLOURS AVAILABLE 


TEXTURED SAND


Ali-Deck uses Qualicoat


Qualicoat


The Ali-Deck system uses a powdercoat process called QUALICOAT: Qualicoat is a quality label organisation committed to maintaining and promoting the quality of coating on aluminium and its alloys for architectural applications.


BS 6496:1984: Specification for powder organic coatings for application and stoving to aluminium alloy extrusions, sheet and preformed sections for


external architectural purposes, and for the finish on aluminium alloy extrusions.


Ali-Deck extrusions are finished using the following EN standards:


EN 12206-1:2004: Paints and varnishes. Coating of aluminium and aluminium alloys for architectural purposes. Coatings prepared from coating powder


EN ISO 2409:2013: Paints and Varnishes, Cross Cut Test.


Our quality department also perform the following tests on our powder coated profiles.


QUALICOAT 2.1: Visual inspection at 3 metres for internal and 5 metres for external extrusions (Our Inspecttorsernal extrusions(Our Inspec


ors


visually inspect at 1 metre as standard) QUALICOAT 2.2: Gloss level check to


within 5% +/- of the manufacturer’s stated level. [EN ISO 2813]


ers


QUALICOAT 2.4.1: Cross Hatch cuts are made at 2mm spacing with one being at 90° to the other cut, tape is then applied, left for 2 minutes and removed to check for adhesion of paint. [EN ISO 2409 2013]


that the material is coated with at least 60 microns of powder, average. [EN ISO 2360]


ISO9227: Acetic Acid Salt Spray Test EN ISO 3231: Resistance to humid


o Humid


or Adhesion of paint. [EN ISO 2409 2013] QUALICOAT 2.3: Thickness checks to see


atmospheres containing Sulphur Dioxide EN ISO 11341: Accelerated weathering test EN ISO 2810: Natural weathering test


(Florida Test). (Carried out on Powder type)


est) (Carried out on Powder


QUALICOAT 2.6: Cupping test is carried out to check for adhesion with the substrate [EN ISO 1520]


QUALICOAT 2.8: Impact test with an energy of 2.5Nm to ensure that the coating adheres to the substrate [EN ISO 6272 / ASTM D2794]


TM D2794],


QUALICOAT 2.7: Bend test on a 5mm Mandrel to ensure adhesion after bending [EN ISO 1519]


O 1519],


QUALICOAT 2.11: Machu test (Accelerated corrosion test) in a solution made up of Sodium Chloride, Acetic Acid and Hydrogen Peroxide at 37°C. Duration 48 hours


QUALICOAT 2.14: Polymerisation test (Wipe with MEK for 30 seconds)


QUALICOAT 2.16: Resistance to boiling water in a pressure cooker. Duration 1 hour 100Kpa


QUALICOAT 2.18: Sawing and drilling to ensure that there is no flaking after cutting (using sharp tools)


Curing Oven temperatures are checked and recorded on a daily basis External checks carried out by the powder


suppliers and our Laboratory in Belgium on random samples of extrusion:


If you are interested in receiving an Ali-Deck sample box please contact us on 0800 389 9072 or email: sales@ablecanopies.co.uk


EN ISO 12206-1: Resistance to mortar (Carried out on Powder type)


EN ISO 6270-2: Constant Climate Condensation Water test


EN ISO 6270-2: Constant Climate Condensation Water test


Our aluminium is sent through a variety of pre-treatment chemical baths that remove a very fine layer off the surface before powder coating.


Our aluminium is sent through a variety of pre-treatment chemical baths that remove a very fine layer off the surface before powder coating.


4 4


EN ISO 12206-1: Resistance to mortar (Carried out on Powder type)


Tel: 0800 389 9072 Tel: 01622 235 672


wwwwww.alideck.co.uk .ablecanopies.c


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20