Production • Processing • Handling
Conveying difficult media to oil and gas fields
Conveying systems have to be adapted to the media and the environment if production is to be efficient under such conditions. Jörg Eitler reports.
D
espite all efforts to promote renewable energies, global demand for crude oil and natural gas has continued unabated. Prices are rising and interest in opening up new
sources, including unconventional sources, is rising with them. Methane from coal seams and highly viscous oil at more than 10,000 mPas are already of commercial interest, but are just as complicated to extract as oil sand mixtures from the Sudanese desert.
Te traditional image of oil production using pumpjacks with their distinctive ‘donkey’ heads is still to be seen on many oil fields around the world.
Progressing cavity pump However, pumpjacks are increasingly being replaced by a less spectacular, but more efficient system - progressing cavity oil pumps. Te primary success of this technology is its ability to convey highly viscous oils at above 50,000mPas while maintaining stable pressure.
What is more, it can do so with almost no pulsation or shear forces, thereby avoiding emulsion effects in oil/water, which would significantly hinder subsequent separation of the oil/water mixtures at the surface. Te volumetric efficiency of a downhole
progressing cavity pump is between 75 and 90 per cent compared to only around 30 per cent for pumpjacks and 35 per cent for electrical centrifugal submersible pumps.
Drive heads As the body of the progressing cavity pump is comparatively slim, it is perfectly suited to the interior of the bore hole. NETZSCH has developed various drive heads for different performance and speed requirements to generate the torque above ground. Te vertical GH drive, for example, comes with 20 to 100H.P. and 3,400Nm torque and is specially designed for large loads and rotation reduction of 1:4. Te right-angled RH version, on the other hand, is used for very low piston-rod speeds and
56
www.engineerlive.com
can be connected to a combustion or hydraulic motor thanks to its particular geometry. Te highly economical DH direct drive is the option for higher rotation speeds up to 500rpm.
In this case, the drive is connected to the pump body itself, which is available in various designs. Te standard NTZ model has low life cycle costs thanks to its small number of wearing parts and is suitable for oil mixtures with up to 40 per cent gas or sand content at up to 160°C. It can achieve conveyance rates of between 0.5 and 300m³/d at maximum 300 bar.
Tis type of pump is used, for example, to extract methane in coal seams in the Qinshui Basin in China.
Te water is removed using the
progressing cavity pump until the gas is released and can be collected. An additional flow controller was integrated into the control system to avoid running dry.
Te NTU pump series, on the other hand, was designed with the focus on low start and operating torques and low interference from temperature or chemicals.
Te steel housing of the spiral form of the inner elastomer stator was
Fig. 2. The volumetric efficiency of progressing cavity pumps is between 75 and 95 per cent.
Fig. 1. Progressing cavity pumps are increasingly replacing traditional pumpjacks.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84