Instrumentation • Electronics
described as a memory system as opposed to a singular device. Another key requirement for a product to truly be
considered to be specialised OEM memory is a unique form factor. This prevents most unauthorised data transfer, helps protect the host system from malicious files and provides a new potential revenue stream when an OEM becomes the exclusive source of new and replacement keys or tokens. Truly rugged portable memory can withstand extreme
temperatures, rough use, sterilisation, chemical exposure, static electricity, dust, dirt, moisture, shock and vibration. To meet these harsh environment requirements, some manufacturers use a solid over-moulding process that encases electronic components in specially engineered composite plastic materials. However, the environmental capabilities of a portable
memory device do little good unless the associated receptacle is also protected. Receptacles in OEM memory systems should also carry ratings consistent with the harsh environments where they will operate. These environmental ratings may include IP ratings, such as IP65 or IP67, or military environmental ratings such as MIL-STD-810. These ratings allow OEM memory systems to operate in harsh environments where consumer memory devices would not survive. OEM memory systems offer a higher number of mating
cycles between the memory device and its mating receptacle: ranging from 50 000 cycles to 200 000 cycles for some OEM receptacles. For example, an OEM memory receptacle rated at 50 000 insertion cycles would last a minimum of thirteen- and-a-half years if used 10 times per day. To put that into perspective, a typical USB connector (rated at 1500 insertion cycles) that sees the same 10 insertions per day will reach its rated cycle life in just five months. Many OEM memory products have been available
unchanged for over 20 years. Lower capacity devices that use EEPROM or NOR flash non-volatile memory technology have a proven track record of long-term availability and are available from multiple manufacturers. This longevity significantly reduces the likelihood that OEMs will have to re-qualify new memory devices when the old one becomes obsolete. While OEM memory systems typically do a better job of
meeting the unique requirements of OEM applications, there are some design considerations that should be weighed against
the benefits offered by consumer memory devices. For instance, is OEM memory affected by the consumer
memory market? Unlike low-capacity OEM memory, high- capacity OEM memory typically utilises NAN D flash technology. As a result, the long-term availability of high- capacity devices is reliant on the consumer market. However, OEM memory systems based on NAN D flash technology typically offer better long-term availability than consumer products by using qualified and consistent sources, featuring configuration control and providing built-to-last designs. Many OEM memory systems are geared towards the
low-capacity applications that are more prevalent in non- consumer embedded systems. However, as previously stated, some newer OEM memory systems offer higher capacities that match those of consumer memory products. Most important to engineers is that the memory solution specified be offered in a range of memory capacities that best meet the specific memory requirements of the system. Deciding between consumer and OEM is the likely first
step in choosing a portable memory solution for an embedded design. In many cases, both will work. However, for successful OEM designs, engineers need to look beyond ‘will it work?’ and consider the long-term implications and the environment in which they will function. While consumer-focused components are less prevalent
in non-consumer OEM designs, it is hard to argue with the convenience, high memory capacity, small size and low cost that USB flash drives, SD cards and other consumer devices can provide. Nonetheless, the short life of consumer memory products is inescapably tied to the fast-paced consumer electronics market. Manufacturers of consumer memory products are not
anti-OEM; they are just meeting the demands of a consumer market that simply does not care about or have a need for performance requirements that are unique to non-consumer, OEM applications. When rugged construction, a high mating cycle life, secure form factors and long-term availability are higher priorities, a purpose-built OEM memory system is likely a better fit. ●
Victoria James is with Nexus GB, Midhurst, West Sussex, UK
www.nexusgb.co.uk
Component and cable accessories catalogue C
omponent and cable accessories supplier, Anixter Component Solutions has launched its new
product catalogue. An addition to the catalogue is the
extensive range of PCB terminal blocks, fuses, fuse holders, indicators and modular push buttons from its new supply partner Camden Boss. With more than 2000 new product
lines, the catalogue provides 300 pages of comprehensive product specifications, making it a tool for both the purchasing and
24
www.engineerlive.com
engineering-based user. Other new Anixter Component
Solutions’ products include silicone and rubber-based potting compounds, flexible conduit contractor packs, energy saving switches and sensors and various new styles of PCB pillars and spacers. ●
Enter 24 or ✔ at
www.engineerlive.com/ede
Anixter Component Solutions is based in Wimborne, Dorset, UK.
www.anixtercomponents.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68