4D FIXED INSTALLATION SEISMIC


(PSDM) can also be limited by velocity error and poor vertical resolution due to the geometry of a salt layer. Such deep velocities models rarely incorporate localised low velocity zones or take into account anisotropy, resulting in velocity models which may be too deep and too steep. Within deeper and hotter wells, resolving low amplitude primary arrivals out of the noise is increasingly challenging. Tis is made more difficult due to the contamination of primary energy at reservoir level by multiple signals generated above the top salt and water bottom and can often be a serious issue when migrated multiples resemble faulted geometry. By having geophones located deep downhole the


up wave travel time to the receiver generated from a reflection is reduced. Tis minimises the amount of energy attenuation, improving the signal strength. Tese geophone tools need to be designed to function within very high borehole temperatures of 180°C plus and pressures reaching 25 000PSI. To enhance oil and gas recovery from ultra low permeability reservoirs (eg, Haynesville Shale, Texas) the geology often requires fracturing. Tis is achieved by the pumping of a proppant through the tight rock to fracture hydrocarbon pathways to the well. As these unconventional rocks fracture, they generate microseismicity. Tis energy will be both as Primary compressional energy and as Secondary shear energy. By employing three component geophones (HX, HY and VZ axis) in a neighbouring monitoring well and recording the time gap between the different velocity P and S waves it is possible, when combined with a velocity model, to calculate the azimuth and distance of the microseism ray path, and so pinpoint the event location (Fig 1). Tis will give crucial information such as fracture height, azimuth and half length along planes of weakness, allowing a more accurate characterisation of the fracture pathway. Tese microseisms are small amplitude and high


frequency, and as such receiver distance from the event needs to be close, and geophone sensitivity needs to be high. When fracturing unconventional geology it is important that the downhole receivers have electronics capable of delivering a high gain, achieve continuous recording and are able to maximise sensitivity by doubling or even quadrupling the number of geophones within a sensor pack, whilst still maintaining a slim tool housing that can be accommodated within deep boreholes. For such surveys to be successful it is critical to


establish the orientation of all the downhole geophone components as the tools can rotate as they travel through the well. Tis is achieved by an offset surface orientation shot triggered from the surface through the geology to the receiver, where the signals recorded on each component can be compared and so orientation


relative to source can be known. Within deep wells and in sub-salt environments, standard surface source orientation shots may not deliver easy to pick, high signal to noise traces. By using a downhole impulsive source such as high energy sparker tool in a proximal well, the shot can be repeated and so can be stacked multiple times to improve the signal to noise ratio. Tis use of a downhole source will also provide a clear time break on the recorded trace and so can be used for QC as any poor signals would suggest bad receiver coupling to the casing and so the operator could simply move the tool string and lock into a better cemented zone (Fig 2).


Key uncertainties such as faulting and other structural geometry play prominent roles in determining the drilling programme. Seismic data quality in such deep environments is often of a low frequency and is usually contaminated with multiple energy. Tis makes characterisation of key uncertainties such as faulting a real struggle. Te data quality can be achieved if high gain, high sensitivity downhole receivers are used. Tese tools must be capable of withstanding the pressures, temperatures and reactive proppant/fluids within the borehole, and should be deployed close to the seismic event with good coupling to the casing. Tis can be augmented with repeatable downhole sources giving clear stackable signals for QC. As this downhole technology continues to advance, the challenges of accurately characterising and monitoring deep unconventional reservoir geology will be met with increasing certainty. 


Enter 23 or ✔ at www.engineerlive.com/ihss


William Wills is a Geoscientist at Avalon Sciences Ltd, Somerset, UK. www.avalonsciences.com


www.engineerlive.com 23


Fig. 2. Ideal stacked trace generated from a high energy repeatable downhole sparker source, recorded by a downhole three component receiver.


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36