This page contains a Flash digital edition of a book.
INDUSTRY AWARENESS ZONE – PROGRAMME


14:30 – 15:00


Nordson UK Speaker - Mike Handscombe Advances in dense-phase technology for greater efficiency and process control


8 years ago, Nordson introduced to the market a new method of delivering powder to the spray gun with the minimum amount of air – dense-phase technology was born!


With the release of the 3rd generation of the powder coating systems utilizing this technology, over 150 automatic lines installed in Europe, we are finding plenty of confirmation to the original expectations and promises of this technology.


The highest level of process control, best quality of automated colour change, improved application efficiency and recessed areas penetration – all are being achieved and enjoyed buy hundreds of manual and automatic powder coaters operating in many industries.


This presentation provides a general overview of this innovative technology and provides facts about those who’ve already experienced it.


Don’t miss this great opportunity to learn how dense-phase technology can enhance your next powder coating system.


15:10 – 15:40


SLF UK Speaker - Jan Den Hartog


DARC (Dark Radiation & Convection) Oven Quick enamelling with energy-saving for powder & paint coating


By combining two established technologies (long-wave infrared radiation and convection) a new enamelling oven has been developed by SLF. It enables economical and energy- efficient hardening, particularly of wet and cataphoretic paints on thick-walled workpieces.


SLF’s new DARC oven consists of heated sidewalls and base which are double-walled such that hot gas can be blown through. The gases are directed in a circular flow and the heat energy released to the walls and the floor and then returned through the gas burner.


Practical feedback shows that it is not only suitable for enamelling powder coating on thick-walled workpieces, but also for quick enamelling/drying on workpieces with different wall thicknesses from 2 mm up to 200 mm.


Shorter heating-up times means process time is reduced and for thick cross sections, the space needed takes only 1/4 of that required for a normal circulating air oven.


Since workpieces with different cross-section thicknesses have different heating-up times, in addition to infrared radiation, convection is switched on for a specific time.


14 SURFACE WORLD september 2013 - show issue


read online @ www.surfaceworld.com


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68  |  Page 69  |  Page 70  |  Page 71  |  Page 72  |  Page 73  |  Page 74  |  Page 75  |  Page 76  |  Page 77  |  Page 78  |  Page 79  |  Page 80  |  Page 81  |  Page 82  |  Page 83  |  Page 84  |  Page 85  |  Page 86  |  Page 87  |  Page 88  |  Page 89  |  Page 90  |  Page 91  |  Page 92  |  Page 93  |  Page 94  |  Page 95  |  Page 96  |  Page 97  |  Page 98  |  Page 99  |  Page 100  |  Page 101  |  Page 102  |  Page 103  |  Page 104  |  Page 105  |  Page 106  |  Page 107  |  Page 108  |  Page 109  |  Page 110  |  Page 111  |  Page 112  |  Page 113  |  Page 114  |  Page 115  |  Page 116  |  Page 117  |  Page 118  |  Page 119  |  Page 120  |  Page 121  |  Page 122  |  Page 123  |  Page 124  |  Page 125  |  Page 126  |  Page 127  |  Page 128  |  Page 129  |  Page 130  |  Page 131  |  Page 132  |  Page 133  |  Page 134  |  Page 135  |  Page 136  |  Page 137  |  Page 138  |  Page 139  |  Page 140  |  Page 141  |  Page 142  |  Page 143  |  Page 144  |  Page 145  |  Page 146  |  Page 147  |  Page 148  |  Page 149  |  Page 150  |  Page 151  |  Page 152  |  Page 153  |  Page 154  |  Page 155  |  Page 156  |  Page 157  |  Page 158  |  Page 159  |  Page 160  |  Page 161  |  Page 162  |  Page 163  |  Page 164  |  Page 165  |  Page 166  |  Page 167  |  Page 168