Console Accessory Specifications
Dump Rims 1. Dump rims can be added to an individual console or around the perimeter of configurations.
2. Dump rim model numbers represent the length of the console edge specified.
3. Specify side dump rims by adding ‘S’ to the end of the model number. Specify angled side rims by adding ‘AS’ to the end of the model number. Side dump rims for consoles with modules are also available.
4.
To order 3-sided dump rims around a single console, order the following quantities: Example: CC603030 Model # DR60
DR30AS DRB-L
Quantity 1 2
2 (to connect dump rims at corners)
When placing two consoles side-by-side with 3-sided dump rims across the full width of the consoles, order the following quantities: Example: (2) CC603030 Model # DR60
DR30AS DRB-L DRB-H
Brackets 5.
Quantity 2 2 2
1 (to connect dump rims across the console backs)
All consoles are shipped with an interior backet to connect adjacent tables. A CX-Clip is a decorative exterior bracket option.
CX-Clip Interior Bracket
Wheels 6.
Wheels (5” diameter) are recommended for consoles up to 60” wide x 36” deep.
7. When ordering consoles with wheels, add ‘W’ to the end of the model number to keep the overall height stan- dard. The normal wheel configuration is four swivel wheels.
Special Features
8. A wrapping feature can be added to CS and CC consoles. This includes a paper-holder mounted to the shelf, a knife bar mounted to the top and a slot in the left side of the console top. Specify alternative locations if desired.
9.
When ordering MRSLOT, specify slot width, depth and location from the edge of the console. MRSLOT-10CONFIG and MRSLOT-13CONFIG preassign hole locations for mail slots at 3” from the console edge, front or rear of console must be specified, consoles up to 48” wide come with (2) mail slot grommet inserts, 48” and wider, (3).
10. CC consoles can be fitted with plunger locks. Order LOCK-M and specify which tables.
11. Special impact-resistant (ABS and stainless steel) surfaces are available. Specify which consoles require the special surface.
12.
Fixed, vertical partitions can be specified for CS or CC consoles. Specify location, spacing and laminate. Partitions can also be field installed by mounting to aluminum channel.
13. To electrify a console, order a pop-up power center and, if necessary, a grommet (MRCBLCO-3).
14. MRDR16-3-20 and MRML-16-S cannot be mounted under CC
consoles.Freestanding pedestals and pedestals with casters can only be mounted under CT, CS or CH consoles.
52
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111