CLEVIS PINS
We supply Clevis Pins to ISO 2341B (DIN 1444) which has a cross- drilled hole for R-Pins or Cotter Pins (see pages 18 and 19). Also available are ISO 2341 with grooves for Circlips to DIN 471.
STANDARDS ISO 2341A
ISO 2341B
ISO 2341 – Circlip ISO 2340A ISO 2340B BS 5894 DIN 1433 DIN 1434
DIN 1435 DIN 1436
DIN 1443 DIN 1444
When specifying Clevis Pins, it should be noted that the nominal length is the total length from under the head to the end of the pin, but the grip length is from under the head to the inside edge of the hole or groove. This is shown in the table under references L1 and G1.
same as 2341 but without hole our stocked programme (for Circlips to DIN 471) Headless, without hole
Headless, with cross-drilled hole at each end obsolete, replaced by ISO 2341 Headless, with or without hole
Similar to ISO 2341 but with smaller diameter head
Similar to ISO 2341 but with larger diameter head
Similar to ISO 2341 but with larger diameter head
Same as ISO 2340 Same as ISO 2341
SIZE RANGE – CLEVIS PINS 12 20
3.2 4
1.1
11.5 5.5
14
22 4 4
1.1
13.4 6
Nominal Diameter ‘d’ Diameter Tolerance Head Diameter ‘H’ Hole Diameter ‘d1’ Head Thickness ‘T’ Circlip Groove ‘C1’ Circlip Groove ‘C2’ Length ‘L2’ Length ‘G1
Lengths ‘L1’ 10
12 14 16 18 20 22
16.9 18.9 20.9 22.9 24.9 27.9 32.9 37.9 42.9 47.9 52.9 57.9 62.9 67.9 72.9 77.9 82.9 87.9 92.9
112.9 24
20 22 24 27 32 37 42 47 52 57 62 67 72 77 82 87 92
112 132
Over 50 mm long ± 0.75
26 28 30 32 35 AVAILABLE TO ORDER
< Non-Standard dimensions < Other materials * ALSO AVAILABLE IN INCH SIZES
40 45 50 55 60 65 70 75 80 85 90 95 100 120 140 Length Tolerances
Up to 10 mm long ± 0.25
E:
sales@technifast.co.uk W:
www.technifast.co.uk
12 – 50 mm long ± 0.5
5 8 min
1.6 1.6 0.7 4.8 2.9
6.7 8.7
10.7 12.7 14.7 16.7 18.7 20.7 22.7 24.7 26.7 28.7 31.7 36.7 41.7 46.7
6 10
1.6 2
0.8 5.7 3.2
L1 – L2 – 1/2 d1 8
10 12 14 16 18 20 22 24 26 28 31 36 41 46 51 56
11.5 13.5 15.5 17.5 19.5 21.5 23.5 25.5 27.5 30.5 35.5 40.5 45.5 50.5 55.5 60.5 65.5 70.5 75.5
8 h11
14 2 3
0.9 7.6 3.5
18
3.2 4
1.1 9.6 4.5
20
3.2 4
1.1
11.5 5.5
22 4 4
1.1
13.4 6
10 12 14
MATERIALS MILD STEEL, ZINC PLATED STAINLESS A2 STAINLESS A4
13.9 15.9 17.9 19.9 21.9 23.9 25.9 28.9 33.9 38.9 43.9 48.9 53.9 58.9 63.9 68.9 73.9 78.9 83.9 88.9 93.9
16.9 18.9 20.9 22.9 24.9 27.9 32.9 37.9 42.9 47.9 52.9 57.9 62.9 67.9 72.9 77.9 82.9 87.9 92.9
112.9
20 22 24 27 32 37 42 47 52 57 62 67 72 77 82 87 92
112 132
Over 50 mm long ± 0.75
20
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42