Track System Single Edge Straight Slides
HepcoMotion track system single edge straight slides retain key features of the double edge slides, with precision ground finish and zone hardened V faces 42 & 43. Standard lengths are available up to 4020mm and unlimited lengths can be achieved by butting slides together. Slides are matched in essential respects both with each other and with their corresponding curved segments. They are ground square on the ends for precision butting and are marked with a reference number and sequence number for identification during installation and for replacement purposes 40 & 41. Slide pairs and opposing slides within a track system are ground to identical lengths
Track system single edge slides, can be used to construct a single edge duplex track system which provides a wide platform for supporting large components with extreme rigidity
18. 17. The large rear face of the single edge slide enables a full width rack
to be machined in the rear face providing for a strong drive. This can be used for the construction of a gear driven duplex track system
B*1 C D M Rack Size A2 A1 A F G F E
Chamfer 0.4 x 45º (5 Positions)
Track slides 42-43
C P H1 H J K L
Track system 40-41
FCC carriage 38-39
Dowel Pin (SDP) For details 42 - 43
Part Number For use with
A ~
A1*3 A2 C D E ±0.2 Ø x Depth F G*3
+0.05 -0.00
H H1 J K L ±0.025
Single Edge
Track segments 46
M*4 Module
P ~ kg/m
TNSE TRIS278, TRES376 21 21.37 8.5 30 90 10 x 5.1 4.7 10 6 2.5 16 2.6 7.4 1 12.35 1.6 TNME TRIM482, TREM655 29 29.37 10.5 30 90 11 x 6.1 6.2 12.5 8 3 20 2.3 9.25 1.25 15.6 2.6
Notes:
1. Standard slide lengths are available in multiples of hole pitch 'D' + (2 x 'C') up to a 4020mm maximum length. Special length slides can be cut to order.
2. Slides in their free unmounted state are not necessarily straight. They should be set to the required straightness when bolting down to the mounting surface at assembly.
3. For track system requirements dimensions 'A1' and 'G' will be matched with corresponding dimensions 'F' and 'I', 46.
4. Single edge slides with a rack, will be supplied in lengths that correspond to multiplies of rack pitch. The position of the ends of the slides is accurately controlled to coincide with the center of the rack root to give perfect running joints for slides and ring segments.
Ordering details: Example:
B (slide length) = 1500mm Part Number
R = Rack cut Slide Leave blank if not required
MLC carriage 48-49
BCP carriage 47
TNME B1500 (R)
(BL)
(16 x SDP)
SDP = Dowel pin (16-off) Leave blank if not required
Bleed Lubrication: BLP = Plain bore insert 52 Leave blank if not required
BLT = Threaded insert 52
Calculations 54-57
45
Bleed
Lubrication 52
XYZ ABC 123
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64